Fiche technique pour ADS8372EVM

{’1‘ TEXAS INSTRUMENTS SLAS451 SBVSOOZ SCLSS77 SL08318 SBOS165 www.ti.com
User's GuideSLAU160 – July 2005
ADS8372EVM
This user's guide describes the characteristics, operation, and use of the ADS837216-bit, 600 kHz, high speed, serial interface Analog-to-Digital converter EvaluationBoard (EVM). A complete circuit description, schematic diagram, and bill of materialsare included.
The following related documents are available on the TI web site at www.ti.com .
Data Sheets: Literature Numbers:
ADS8372 SLAS451
REF1004C-2.5 SBVS002
SN74AHC1G125 SCLS377
THS4131 SLOS318
OPA627AU SBOS165
Contents1 EVM Overview ............................................................................................................... 22 Analog Interface .............................................................................................................. 23 Digital Interface .............................................................................................................. 44 Power Supplies .............................................................................................................. 55 Using the EVM ............................................................................................................... 56 ADS8372EVM Bill Of Materials ............................................................................................ 78 Board Layers ................................................................................................................. 99 Schematics .................................................................................................................. 11
List of Figures
1 Input Buffer Circuit ........................................................................................................... 32 Top Layer ..................................................................................................................... 93 Power Plane .................................................................................................................. 94 Ground Plane ............................................................................................................... 10
5 Bottom Layer ................................................................................................................ 10
List of Tables
1 Analog Input Connector ..................................................................................................... 2
2 Jumper Setting ............................................................................................................... 4
3 Pinout for Serial Control Connector P2 ................................................................................... 4
4 Power Supply Test Points .................................................................................................. 5
5 Power Connector (J3) Pin Out ............................................................................................. 5
7 ADS8372EVM Bill of Materials ............................................................................................. 7
SLAU160 – July 2005 ADS8372EVM 1
{’4‘ TEXAS INSTRUMENTS www.|l.cnm
www.ti.com
1 EVM Overview
1.1 Features
2 Analog Interface
2.1 Signal Conditioning
EVM Overview
•Full-featured evaluation board for the ADS8372 16-bit, 600 kHz, single channel, high-speedserial-interface analog-to-digital converter (ADC)•On board signal conditioning•On board reference•Input and output digital buffer
The ADS8372EVM ships with buffer U13 configured in a unity-gain, single-ended to differential outconfiguration. The common-mode voltage pin of the THS4131 is factory set to 2.0 V on the evaluationmodule, and can be adjusted using potentiometer RP1. The potentiometer connects between the output ofreference buffer U3 and ground. The single-ended input signal can be applied at pin-connector P1 pin 2 orvia SMA connectors J2 (non-inverting input). The buffer circuit can be reconfigured for a fully differentialinput by installing resistors R4 and R31 and removing R16. The inverting leg of the differential signal canbe connected to connector P1 pin 1 or SMA connector J1 (inverting input). See Table 1 for the pinout ofthe analog connector, P1. See Section 9 for the EVM schematic diagrams.
The analog-to-digital converter accepts a pseudo-bipolar differential input. A pseudo-bipolar differentialsignal is a differential signal that has a common-mode voltage such that each leg is always equal to orabove zero volts. The common mode voltage should be half the reference voltage. The peak-to-peakamplitude on each input leg can be as large as the reference voltage.
Table 1. Analog Input Connector
Description Signal Name Connector pin# Signal Name Description
Inverting Input –IN P1.1 P1.2 +IN Non-inverting Input
Reserved N/A P1.3 P1.4 N/A Reserved
Reserved N/A P1.5 P1.6 N/A Reserved
Reserved N/A P1.7 P1.8 N/A Reserved
Pin tied to Ground AGND P1.9 P1.10 N/A Reserved
Pin tied to Ground AGND P1.11 P1.12 N/A Reserved
Reserved N/A P1.13 P1.14 N/A Reserved
Pin tied to Ground AGND P1.15 P1.16 N/A Reserved
Pin tied to Ground AGND P1.17 P1.18 N/A Reserved
Reserved N/A P1.19 P1.20 REF+ External Reference Input
It is a recommended practice to buffer the analog input to any SAR-type converter with a high-speed,low-noise amplifier with fast settling time. The amplifier circuit shown in Figure 1 is the buffer circuit usedon the ADS8372EVM. This circuit consists of the THS4131, a high-speed, low-noise, fully differentialamplifier configured as a single-ended in to differential out, unity gain buffer. This circuit was optimized toachieve the AC specifications (i.e., SNR, THD, SFDR, etc.) listed in the ADS8372 data sheet.
The type of input capacitors used in the signal path can make a few decibels of difference in ACperformance. Polypropylene or C0G-type capacitors are recommended for the input signal path.
ADS8372EVM 2 SLAU160 – July 2005
*9 TEXAS INSTRUMENTS www.|l.cnm 1 k9 -Vcc 1 kg 55 pF coe \ \ 2552
www.ti.com
_
+
+
−
1 F
0.1 F
1 F
0.1 F
VCC
−VCC
2.048 V
1 k
68 pF
C0G
1 k
68 pF
C0G
1 k
1 k
VIN
THS4131
25
25
6800 pF
C0G
(+) IN
(−) IN
2.2 Reference Voltage
Analog Interface
Polypropylene capacitors cause the least distortion of the input signal and have excellent long-termstability, but are expensive and bulky. C0G ceramic capacitors cost less, come in smaller packages andperform as well as polypropylene capacitors in many applications, but are not as stable over time andtemperature. The 68 pF and 6800 pF capacitors installed on the EVM are low-cost C0G type,manufactured by TDK Corporation.
Figure 1. Input Buffer Circuit
The EVM allows the designer to select internal, on-board, or user-supplied reference-voltage sources. Theinternal reference is a 4.096 V reference voltage generated by the ADS8372 on pin 9. The on-boardreference can be either a REF3040 (U1) or REF1004-2.5 (U14). The EVM ships with the REF1004-2.5installed. The reference amplifier, U3, is set for a gain of 1.6, enabling it to take a 2.5 V input and output4.1 V for use with the converter, or as part of the common-mode voltage circuit for the input buffer (U13).The user-supplied reference voltage is applied to connector P1 pin 20, and can be routed through thereference buffer and filtered, if desired. The EVM allows a number of configurations. Refer to Table 1 forjumper settings, or the full schematic in Section 9 for more information. The common footprint for U14allows users to evaluate this converter with various reference ICs.
The EVM ships with the internal reference tied directly to the reference pin of the converter.
SLAU160 – July 2005 ADS8372EVM 3
{’4‘ TEXAS INSTRUMENTS www.|l.cnm
www.ti.com
3 Digital Interface
Digital Interface
Table 2. Jumper Setting
Reference Pins/PadsDescriptionDesignator
1-2 2-3
SJP1 Buffer onboard reference (REF1004-2.5) Shorted
(1)
Open
Buffer user supplied reference voltage applied at P1 pin 20. Open Shorted
SJP2 Connect external reference directly to SJP4 Shorted
(1)
Open
Connect buffered external reference to SJP4 Open Shorted
SJP3 Connect U3 negative supply to ground Shorted Open
Connect U3 negative supply to –VCC Open Shorted
(1)
SJP4 Connect internal reference to REFIN Shorted
(1)
Open
Connect external reference to REFIN Open Shorted
SJP5 Connect common-mode voltage to VOCM pin of THS4131 Shorted
(1)
N/A
W1 Connect +5VD to BVDD Shorted
(1)
Open
Connect +3.3VD to BVDD Open Shorted
W3 Set power down signal (PD) high Shorted N/A
W4 Set frame sync signal (FS) high Shorted N/A
W5 Set chip select signal (CS) low Shorted
(1)
N/A
(1)
Factory Installed
The ADS8372EVM is designed for easy interfacing to multiple platforms. Samtec plug and socketconnectors provide a convenient dual row header/socket combination at P1 and P2 to plug into prototypeboards or ribbon cable over to user system boards.
The digital input and output signals for the converter is available at connector P2 on the ADS8372EVM,see Table 3 for the connector pinout.
Table 3. Pinout for Serial Control Connector P2
Description Signal Name Connector Pin Signal Name Description
Chip Select CS P2.1 P2.2 N/A Reserved
Serial Clock SCLK P2.3 P2.4 DGND Ground
Reserved N/A P2.5 P2.6 N/A Reserved
Frame Sync FS P2.7 P2.8 N/A Reserved
Reserved N/A P2.9 P2.10 N/A Reserved
Reserved N/A P2.11 P2.12 N/A Reserved
Serial Data Out SDO P2.13 P2.14 N/A Reserved
BUSY BUSY P2.15 P2.16 N/A Reserved
Convert Start CONVST P2.17 P2.18 DGND Ground
Power down PD P2.19 P2.20 N/A Reserved
ADS8372EVM 4 SLAU160 – July 2005
{’4‘ TEXAS INSTRUMENTS www.|l.cnm
www.ti.com
4 Power Supplies
5 Using the EVM
5.1 Reference Design
Power Supplies
The EVM accepts four power supplies•A differential ( ±) dc supply for the dual-supply op amps. The maximum recommended voltage is ±15Vdc
•A single +5.0 V dc supply for the analog section of the board (A/D + Reference).•A single +5.0 V or +3.3 V dc supply for digital section of the board (A/D + buffers).
There are two ways to provide these voltages. The first is to connect the voltages to the test points listedin Table 4 .
Table 4. Power Supply Test Points
Test Point Signal Description
TP1 +VA Connect +15.0 V dc supply for amplifier
TP2 –VA Connect –15.0 V dc supply for amplifier
TP3 +BVDD Apply +3.3 V dc or +5.0 V dc. See ADC data sheet for full range.
TP4 +AVCC Apply +5.0 V dc
The second is to use the power connector J3, and derive the voltages elsewhere. Table 5 gives the pinoutfor J3. If using this connector, set W1 jumper to connect +3.3VD or +5VD from J3 to +BVDD. Shunt pins1-2 to select +5VD, or pins 2-3 to select +3.3VD as the source for the digital-buffer-voltage supply(+BVDD).
Table 5. Power Connector (J3) Pin Out
Signal J1 Pin Signal
+VA(+15V) 1 2 –VA(–15 V)
+5VA 3 4 N/C
DGND 5 6 AGND
N/C 7 8 N/C
+3.3VD 9 10 +5VD
The ADS8372EVM serves three functions:
1. As a reference design2. As a prototype board3. As a software test platform
As a reference design, the ADS8372EVM contains the essential circuitry to showcase the analog-to-digitalconverter. This essential circuitry includes the input amplifier, reference circuit, and buffers. The EVManalog-input circuit is optimized for a 100-kHz input signal; therefore, users may need to adjust theresistor and capacitor values to accommodate higher frequencies. In ac-type applications where signaldistortion is concern, polypropylene or C0G type capacitors are recommended for use in the signal path.
Typical fully-differential amplifiers configured for single-ended in to differential out can distort the signal inan attempt to equalize the input pins. This distortion is specially evident when step inputs are applied.Therefore, users who will be applying a step input to the converter should use discrete amplifiers for thesingle-ended-to-differential conversion of the signal. The Differential Input, Differential Output Configur-ation circuit shown in the Theory of Operation section of the ADS8372 datasheet (literature numberSLAS451) can be used. In applications where the input is continuous, the single amplifier solution usingthe THS4131, can effectively drive the converter inputs.
SLAU160 – July 2005 ADS8372EVM 5
{5i TEXAS INSTRUMENTS www.|l.cnm (SLAU104
www.ti.com
5.2 Prototype Board
5.3 Software Test Platform
Using the EVM
As a prototype board, the buffer circuit has resistor pads for configuring the input as either single-ended orfully differential input. The input circuit can be modified to accommodate user prototype needs, whether itbe evaluating another differential amplifier or limiting noise for best performance. The analog, power, anddigital connectors can be made to plug into a standard 0.1” breadboard or ribbon cables to interfacedirectly to FPGAs or processors.
As a software test platform, connectors P1 and P2 plug into the serial interface connectors of the 5-6Kinterface card. The 5-6K interface card plugs into the C5000 and C6000 Digital Signal Processor starterkits (DSK). Refer to the 5-6K Interface Card User’s Guide (SLAU104 ) for more information.
ADS8372EVM 6 SLAU160 – July 2005
J9 TEXAS INSTRUMENTS www.|l.cnm dalaconvaggs@|i (Leom
www.ti.com
6 ADS8372EVM Bill Of Materials
ADS8372EVM Bill Of Materials
The following table contains a complete bill of materials for the ADS8372EVM. The schematic diagram isalso provided for reference. Contact the Product Information Center or email dataconvapps@list.ti.com forquestions regarding this EVM.
Table 7. ADS8372EVM Bill of Materials
Reference Manufacturer'sQTY Value Footprint Manufacturer DescriptionDesignators Part Number
1 49.9 R1 603 Panasonic - ECG or ERJ-3EKF49R9V RES 49.9 Ω1/16 W 1% 0603 SMDAlternate
1 1.2 k ΩR2 603 Yageo America or 9C06031A1201FKHFT RES 1.20 k Ω1/10 W 1% 0603 SMDAlternate
4 NI R3 R4 R5 R31 805 NOT INSTALLED NOT INSTALLED
8 100 ΩR6 R21 R22 603 Panasonic - ECG or Alter- ERJ-3EKF1000V RES 100 Ω1/16 W 1% 0603 SMDR23 R24 R25 nateR26 R27
1 100 ΩR7 805 Panasonic - ECG or ERJ-6ENF1000V RES 100 Ω1/10 W 1% 0805 SMDAlternate
7 10 k ΩR8 R10 R11 603 Panasonic - ECG or ERJ-3EKF1002V RES 10.0K Ω1/16 W 1% 0603 SMDR12 R13 R32 AlternateR39
1 910 ΩR14 805 Panasonic - ECG or ERJ-6GEYJ911V RES 910 Ω1/8 W 5% 0805 SMDAlternate
3 1 k ΩR15 R16 R17 805 Panasonic - ECG or ERJ-6ENF1001V RES 1.00 k Ω1/10 W 1% 0805 SMDAlternate
1 768 ΩR18 603 Panasonic - ECG or ERJ-3EKF7680V RES 768 Ω1/16 W 1% 0603 SMDAlternate
2 0 ΩR19 R36 603 Panasonic - ECG or ERJ-3GEY0R00V RES ZERO Ω1/16 W 5% 0603 SMDAlternate
2 1 k ΩR28 R29 603 Panasonic - ECG or ERJ-3EKF1001V RES 1.00 k Ω1/16 W 1% 0603 SMDAlternate
1 NI R30 603 NOT INSTALLED NOT INSTALLED
2 24.9 ΩR33 R34 805 Panasonic - ECG or ERJ-6ENF24R9V RES 24.9 Ω1/10 W 1% 0805 SMDAlternate
1 49.9 k ΩR35 805 Panasonic - ECG or ERJ-6ENF4992V RES 49.9 k Ω1/10 W 1% 0805 SMDAlternate
2 0 R37 R38 1206 Panasonic - ECG or ERJ-8GEY0R00V RES 0 Ω1/4 W 5% 1206 SMDAlternate
1 47 µF C1 1206 TDK Corporation or C3216X5R0J476M CAP CER 47 µF 6.3 V X5R 20% 1206Alternate
5 1 µF C2 C3 C4 C5 805 TDK Corporation or C2012X7R1E105K CAP CER 1.0 µF 25 V X7R 0805 T/RC45 Alternate
3 1 µF C6 C7 C44 603 TDK Corporation or C1608X5R1A105KT CAP CER 1.0 µF 10 V X5R 10% 0603Alternate
15 0.1 µF C8 C9 C10 603 TDK Corporation or C1608X7R1E104K CAP CER 0.10 µF 25 V X7R 10% 060C11 C12 C13 AlternateC17 C18 C19C20 C21 C22C23 C26 C28
5 2.2 µF C14 C15 C24 603 TDK Corporation or C1608X5R1A225MT CAP CER 2.2 µF 6.3 V X5R 20% 0603C25 C27 Alternate
5 NI C29 C42 603 NOT INSTALLED NOT INSTALLED
9 0.01 µF C35 C36 C37 603 TDK Corporation or C1608X7R1H103KT CAP CER 10000 pF 50 V X7R 10% 0603C38 C39 C40 AlternateC41 C55 C58
1 10 µF C34 3528 Kemet or Alternate T491B106K016AS CAPACITOR TANT 10 µF 16 V 10% SMD
1 6800 µF C46 C43 C63 805 TDK Corporation or C2012C0G1H682J CAP CER 6800 pF 50 V C0G 5% 0805Alternate
4 10 µF C47 C48 C49 1206 TDK Corporation or C3216X5R1C106KT CAP CER 10 µF 16 V X5R 20% 1206C50 Alternate
4 10 µF C51 C52 C53 6032 Pansonic - ECG or ECS-T1EC106R CAP 10 µF 25 V Tantalum TE SMDC54 Alternate
2 68 pF C32 C33 603 TDK Corporation or C1608C0G1H680J CAP CER 68 pF 50 V C0G 5% 0603Alternate
2 0.01 µF C56 C57 1206 TDK Corporation or C3216X7R1H103KT CAP 10000 pF 50 V CERAMIC X7R 1206Alternate
4 1000 pF C59 C60 C61 603 TDK Corporation or C1608C0G1H102KT CAP CER 1000 pF 50 V C0G 0603 T/RC62 C64 Alternate
2 NI C30 C31 805 NOT INSTALLED NOT INSTALLED 1/10 W 0805 Chip resistor
SLAU160 – July 2005 ADS8372EVM 7
{’4‘ TEXAS INSTRUMENTS www.|l.cnm
www.ti.com
ADS8372EVM Bill Of Materials
Table 7. ADS8372EVM Bill of Materials (continued)
Reference Manufacturer'sQTY Value Footprint Manufacturer DescriptionDesignators Part Number
1 10 k ΩRP1 BOURNS_3296Y Bourns Inc. 3296Y-1-103 POT 10 k Ω3/8" SQ CERM SL MT
4 L1 L2 L3 L4 805 TDK Corporation MMZ2012R601A FERRITE CHIP 600 Ω500 mA 0805
2 NI U1 U2 3-SOT-23 NOT INSTALLED NOT INSTALLED REF3040 50 ppm/ °C, 50 µA in SOT23-3CMOS voltage reference
1 U3 8-SOP(D) Texas Instruments OPA627AU DiFet amplifier
7 U5 U6 U7 U8 5-SOT(DBV) Texas Instruments SN74AHC1G125DBVR Single bus buffer gate/line driver with 3-stateU9 U10 U11 output
1 ADS8372 U12 28-PQFP(QFN) Texas Instruments ADS8372IBRHPT ADS8372 16-bit serial 600 ksps
1 THS4131 U13 8-SOP(D) Texas Instruments THS4131ID High-speed low noise, fully differential I/Oamplifiers
1 REF1004-2.5 U14 8-SOP(D) Texas Instruments REF1004C-2.5 2.5 V Micropower voltage reference
1 3POS_JUMPER W1 3pos_jump Samtec TSW-103-07-L-S 3 Position jumper _ 0.1" spacing
3 2POS_JUMPER W3 W4 W5 2pos_jump Samtec TSW-102-07-L-S 2 Position jumper _ 0.1" spacing
1 SJP2 SJP5 SJP2 NOT INSTALLED NOT INSTALLED Pad 2 position jumper
4 SJP3 SPJ1 SPJ2 SJP3 NOT INSTALLED NOT INSTALLED Pad 3 position jumperSPJ3 SPJ4
2 SMA_PCB_MT J1 J2 SMA_JACK Johnson Components Inc. 142-0701-301 Right angle SMA connector
1 Power supply J3 5x2x0.1_ Samtec SSW-105-22-S-D-VS 0.025" SMT socket - bottom side of PWBSMT_SOCKET
1 Samtec TSM-105-01-T-D-V-P 0.025" SMT plug - top side of PWB
2 10x2x0.1 P1 P2 10x2x0.1_ Samtec SSW-110-22-S-D-VS 0.025" SMT socket - bottom side of PWBSMT_LPUG_
&_SOCKET
2 Samtec TSM-110-01-T-D-V-P 0.025" SMT plug - top side of PWB
10 TP_0.025 TP1 TP2 TP3 test_point2 Keystone Electronics 5000K-ND Test point PC MINI 0.040"D blackTP4 TP5 TP6TP7 TP8 TP11TP12
4 TP_0.25 TP10 TP13 test_point2 Keystone Electronics 5001K-ND Test point PC MINI 0.040"D blackTP9 TP14
ADS8372EVM 8 SLAU160 – July 2005
{5i TEXAS INSTRUMENTS www.ll.com AD<8382evm e="" a="" a="" r\="" m="" n="" 375w="" 5nd="" "rm="" m="" te‘h="" (—3200="" (ml)="" h="" "him="" "hill"="" c..="" "him="" llllllll="" ..="" ..="" llllllll="" i="">
www.ti.com
8 Board Layers
Board Layers
Figure 2. Top Layer
Figure 3. Power Plane
SLAU160 – July 2005 ADS8372EVM 9
INSTRUMENTS wwaLnom fl TEXAS 9.8885 88888 B33880 38888 N c .. alik\ a {J}; cum? HAHN, n‘ o F umnammgaa 583 cc ac mum mumggagamm
www.ti.com
Board Layers
Figure 4. Ground Plane
Figure 5. Bottom Layer
ADS8372EVM 10 SLAU160 – July 2005
{5i TEXAS INSTRUMENTS www.|l.cnm
www.ti.com
9 Schematics
Schematics
Schematic diagrams are appended following this page.
SLAU160 – July 2005 ADS8372EVM 11
m m)
123456
A
B
C
D
6
54321
D
C
B
Ati
12500 TI Boulevard. Dallas, Texas 75243
TITLE:
SHEET: OF:
FILE: SIZE:
REV:
Drawn By:
Engineer:
Revision History
REV ECN Number Approved
DOCUMENT CONTROL #:
12
BlockDiagram.sch
A
DATE: 30-Jun-2005
ADS8372EVM/ADS8382EVM
6458774
Serial Control
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
P2
Analog Input
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
P1
+VA
-VA
CS
FS
PD
SCLK
+AVCC
+VA
-VA
+BVDD
B_SDO
+IN
EXT_REF
B_BUSY
CONVST
-IN
Circuits
J2
+AVCC
+BVDD
Lijoy Philipose
Lijoy Philipose
1 2
3 4
5 6
7 8
910
J3
Power Supply
+VA -VA
+5VD
AGND
+AVCC
TP4
TP3
TP1
TP2
DGND
W1
+3.3VD
CS
SCLK
FS
B_SDO
PD
CONVST
B_BUSY
J1
1 2 3 4 5 6
A
B
C
D
6
54321
D
C
B
Ati
12500 TI Boulevard. Dallas, Texas 75243
TITLE:
SHEET: OF:
FILE: SIZE:
REV:
Drawn By:
Engineer:
Revision History
REV ECN Number Approved
DOCUMENT CONTROL #:
22
Circuits
A
DATE: 30-Jun-2005
Circuits
6458774
C35
0.01uF
C20
0.1uF
C38
0.01uF
C24
2.2uF
C25
2.2uF
C39
0.01uF
C27
2.2uF
C41
0.01uF
+5VCC
+5VCC
+5VCC
C14
2.2uF
C36
0.01uF
+5VCC
C15
2.2uF
C37
0.01uF
+VBD
EXT_REF
31
2
SJP4
+
C34
10uF
C1
47uF
R18
768
R6
100
C29
NI
+VCC
C2
1uF
C8
0.1uF
-VCC
C9
0.1uF
C3
1uF
IN
1
OUT
2GND 3
U1
NI
+5VCC
R2
1.2k
3 1
2
SJP2
3 1
2
SJP1
R19
0
Lijoy Philipose
Lijoy Philipose
3
2
6
74
5
1
U3
OPA627
R1
50
31
2
SJP3
TP5
CS
SCLK
FS
PD
B_SDO
CS
SCLK
FS
R11
10k
R12
10k
+VBD
R13
10k
PD
+
C54
10uF
+C51
10uF
TP8 +5VCC
C55
0.01uF
C11
0.1uF
TP9 TP7 +VBD
C58
0.01uF
C13
0.1uF
TP14
C47
10uF
C50
10uF
C62
1000pF
C59
1000pF
+AVCC
+BVDD
L3
MMZ2012R601A
+C53
10uF
+C52
10uF
C6
1uF
C7
1uF
C56
0.01uF
C57
0.01uF
TP11
TP12
TP13
+VCC
-VCC
C48
10uF
C49
10uF
C60
1000pF
C61
1000pF
+VA
-VA
TP10
AGND 1
AGND 2
+VA 3
AGND 4
AGND 5
VA 6
REFM 7
REFIN
8
REFOUT
9
NC
10
IN+
11
IN-
12
NC
13
VA
14
AGND
15
VA
16
VA
17
AGND
18
AGND
19
BVDD
20
BGND
21
BUSY 22
SDO 23
SCLK 24
CONVST 25
CS 26
FS 27
PD 28
U12
ADS8372/ADS8382
CONVST
SDO
BUSY
B_BUSY
CONVST
B_PD
B_FS
B_CS
B_CONVST
B_SCLK
R8
10k
R10
10k
W3 W4
W5
C26
0.1uF
C40
0.01uF
+5VCC
R28 1k
R29 1k
R21 100
R22 100
R23 100
R24 100
R25 100
R26
100
R27
100
C42 NI
C43 NI R30
NI
+VBD
+VBD C23
0.1uF
+VBD
C17
0.1uF OE 1
A2
GND 3
Y
4
VCC
5
U5
SN74AHC1G125
OE 1
A2
GND 3
Y
4
VCC
5
U7
SN74AHC1G125
OE 1
A2
GND 3
Y
4
VCC
5
U6
SN74AHC1G125
C18
0.1uF
OE 1
A2
GND 3
Y
4
VCC
5
U8
SN74AHC1G125
OE 1
A2
GND 3
Y
4
VCC
5
U9
SN74AHC1G125
OE
1
A
2
GND
3Y4
VCC 5
U10
SN74AHC1G125
OE
1
A
2
GND
3Y4
VCC 5
U11
SN74AHC1G125
+VBD
C19
0.1uF
+VBD
C21
0.1uF
+VBD
C22
0.1uF
+VBD
+VBD C28
0.1uF
-IN
-VCC
+VCC
C33
68pF
R17
1k
C12
0.1uF
C4
1uF
C5
1uF
C10
0.1uF
R33
25
C30
NI
R15
1k
R34
25
C31
NI
+IN
C45
1uF
R7
100
R14
910
R3
NI
R16
1k
TP6 5
4
8
1
2
+
-
VOCM
VOUT-
VOUT+
36
+VCC
-VCC
7
NC U13
THS4131
12
SJP5
IN
1
OUT
2GND 3
U2
NI
+5VCC
C44
1uF
C46
6800pF
R4
NI
R31
NI
R5
NI
C32 68pF
*
*
*
NC
1
+VIN
2
EN
3
GND
4NC 5
VREF 6
NC 7
NC 8
U14
REF1004-2.5
+5VCC
C64
NI
C63
NI
R35
49.9k
+5VCC
R36
0
R38 0
R37 0
RP1
10K
R32
10K
R39
10K
L4
MMZ2012R601A
L2
MMZ2012R601A
L1
MMZ2012R601A
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated