ADC0801-05 Datasheet by Texas Instruments

Datasheet Feedback/Errors

I TEXAS INSTRUMENTS w T EIS‘Jﬂ‘U; mm. +1 LSB ummvnnw +3” LSB A TL): W |_ +I/2 L58 .0” , ._L nun} ERROR a *1/2 LS! 3/4 LSB *1 [SB ANALOG INPUT Wm)

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

ADC080x 8-Bit, µP-Compatible, Analog-to-Digital Converters

1 Features 3 Description

The ADC0801, ADC0802, ADC0803, ADC0804, and

1• Compatible With 8080-µP Derivatives – No ADC0805 devices are CMOS 8-bit successive

Interfacing Logic Needed – Access Time 135 ns approximation converters (ADC) that use a differential

• Easy Interface to All Microprocessors, or Operates potentiometric ladder — similar to the 256R products.

as a Stand-Alone Deivce These converters are designed to allow operation

with the NSC800 and INS8080A derivative control

• Differential Analog Voltage Inputs bus with Tri-state output latches directly driving the

• Logic Inputs and Outputs Meet Both MOS and data bus. These ADCs appear like memory locations

TTL Voltage-Level Specifications or I/O ports to the microprocessor and no interfacing

• Works With 2.5-V (LM336) Voltage Reference logic is needed.

• On-Chip Clock Generator Differential analog voltage inputs allow increasing the

• 0-V to 5-V Analog Input Voltage Range With common-mode rejection and offsetting the analog

Single 5-V Supply zero input voltage value. In addition, the voltage

reference input can be adjusted to allow encoding

• No Zero Adjust Required any smaller analog voltage span to the full 8 bits of

• 0.3-Inch Standard Width 20-Pin DIP Package resolution.

• 20-Pin Molded Chip Carrier or Small Outline

Package Device Information(1)

• Operates Ratiometrically or With 5 VDC, 2.5 VDC,PART NUMBER PACKAGE BODY SIZE (NOM)

or Analog Span Adjusted Voltage Reference ADC0801, PDIP (20) 26.073 mm × 6.604 mm

ADC0803

• Key Specifications PDIP (20) 26.073 mm × 6.604 mm

ADC0802,

– Resolution: 8 Bits ADC0804 SOIC (20) 12.80 mm × 7.50 mm

– Total Error: ±1/4 LSB, ±1/2 LSB and ±1 LSB (1) For all available packages, see the orderable addendum at

– Conversion Time: 100 µs the end of the data sheet.

2 Applications

• Operates With Any 8-Bit µP Processors or as a

Stand-Alone Device

• Interface to Temp Sensors, Voltage Sources, and

Transducers

Typical Application Schematic ADC0801 Specified With ±¼ LSB Accuracy

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Table of Contents

8.2 Functional Block Diagram....................................... 12

1 Features.................................................................. 18.3 Feature Description................................................. 12

2 Applications ........................................................... 18.4 Device Functional Modes........................................ 14

3 Description ............................................................. 19 Application and Implementation ........................ 15

4 Revision History..................................................... 29.1 Application Information............................................ 15

5 Pin Configuration and Functions......................... 39.2 Typical Applications ................................................ 22

6 Specifications......................................................... 49.3 System Examples ................................................... 40

6.1 Absolute Maximum Ratings ...................................... 410 Power Supply Recommendations ..................... 48

6.2 ESD Ratings.............................................................. 411 Layout................................................................... 48

6.3 Recommended Operating Conditions....................... 411.1 Layout Guidelines ................................................. 48

6.4 Thermal Information.................................................. 412 Device and Documentation Support ................. 49

6.5 Operating Ratings ..................................................... 512.1 Related Links ........................................................ 49

6.6 Electrical Characteristics........................................... 512.2 Community Resources.......................................... 49

6.7 AC Electrical Characteristics..................................... 512.3 Trademarks........................................................... 49

6.8 Typical Characteristics.............................................. 812.4 Electrostatic Discharge Caution............................ 49

7 Parameter Measurement Information ................ 10 12.5 Glossary................................................................ 49

7.1 Tri-State Test Circuits and Waveforms................... 10 13 Mechanical, Packaging, and Orderable

8 Detailed Description............................................ 11 Information ........................................................... 49

8.1 Overview ................................................................. 11

4 Revision History

Changes from Revision B (Feburary 2013) to Revision C Page

• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional

Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device

and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1

• Removed Ordering Information table .................................................................................................................................... 4

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS E— 1 20 —VCC(0R VREF) ﬁ— 2 19 —CLKR W— 3 13 —DBO(LSB) CLKIN— 4 17 —DB1 W— 5 15 —DBZ le(+)— s 15 —DBS le(-)— 7 14 —D34 AGND— s 13 —DBS vREF/z— 9 12 —DBG DGND— 1o 11 —DB7(MSB)

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

5 Pin Configuration and Functions

NFH and DW Package

20-Pin PDIP and SOIC

Top View

Pin Functions

PIN I/O DESCRIPTION

NO. NAME

1 CS I Chip Select

2 RD I Read

3 WR I Write

4 CLK IN I External Clock input or use internal clock gen with external RC elements

5 INTR O Interrupt request

6 VIN(+) I Differential analog input+

7 VIN(–) I Differential analog input–

8 A GND I Analog ground pin

9 VREF/2 I Reference voltage input for adjustment to correct full scale reading

10 D GND I Digital ground pin

11 DB7 O Data bit 7

12 DB6 O Data bit 6

13 DB5 O Data bit 5

14 DB4 O Data bit 4

15 DB3 O Data bit 3

16 DB2 O Data bit 2

17 DB1 O Data bit 1

18 DB0 (LSB) O Data bit 0

19 CLK R I RC timing resistor input pin for internal clock gen

20 VCC (or VREF) I +5V supply voltage, also upper reference input to the ladder

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)(2)

MIN MAX UNIT

Supply voltage (VCC)(3) 6.5 V

Logic control inputs –0.3 18

Voltage V

At other input and outputs –0.3 (VCC +0.3)

Dual-In-Line Package (plastic 260

Lead Temperature Dual-In-Line Package (ceramic) 300

(Soldering, 10 Surface Mount Package Vapor Phase (60 seconds) 215 °C

seconds) Infrared (15 seconds) 220

Storage Temperature –65 150

Package Dissipation at TA= 25°C 875 mW

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended

Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) If Military/Aerospace specified devices are required, contact the Sales Office/Distributors for availability and specifications.

(3) A Zener diode exists, internally, from VCC to GND and has a typical breakdown voltage of 7 VDC.

6.2 ESD Ratings

VALUE UNIT

V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±800 V

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)

MIN NOM MAX UNIT

VCC 4.5 5 5.5 V

Analog Input Voltage GND – 0.05 VCC + 0.05 VDC

6.4 Thermal Information

ADC080x ADC0802,

ADC0804

THERMAL METRIC(1) UNIT

NFH (PDIP) DW (SOIC)

20 PINS 20 PINS

RθJA Junction-to-ambient thermal resistance 38.5 63.8 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 23.4 27.2 °C/W

RθJB Junction-to-board thermal resistance 19.5 31.8 °C/W

ψJT Junction-to-top characterization parameter 8.7 5.7 °C/W

ψJB Junction-to-board characterization parameter 19.4 31.3 °C/W

RθJC(bot) Junction-to-case (bottom) thermal resistance — — °C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report, SPRA953.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

6.5 Operating Ratings

over operating free-air temperature range (unless otherwise noted)(1)(2).

MIN MAX UNIT

ADC0804LCJ –40 85

ADC0801/02/03/05LCN –40 85

Temperature °C

ADC0804LCN 0 70

ADC0802/04LCWM 0 70

Range of VCC 4.5 6.3 VDC

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not

apply when operating the device beyond its specified operating conditions.

(2) All voltages are measured with respect to GND, unless otherwise specified. The separate A GND point should always be wired to the D

GND.

6.6 Electrical Characteristics

The following specifications apply for VCC = 5 VDC, TMIN ≤TA≤TMAX and fCLK = 640 kHz (unless otherwise specified).

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

ADC0801: Total Adjusted Error(1) With Full-Scale Adj. (See Full-Scale) ±1/4

ADC0802: Total Unadjusted VREF/2=2.500 VDC ±1/2

Error(1)

ADC0803: Total Adjusted Error(1) With Full-Scale Adj. (See Full-Scale) ±1/2 LSB

ADC0804: Total Unadjusted Error VREF/2=2.500 VDC ±1

(1)

ADC0805: Total Unadjusted Error VREF/2-No Connection ±1

(1)

ADC0801/02/03/05 2.5 8

VREF/2 Input Resistance (Pin 9) kΩ

ADC0804 (2) 0.75 1.1

Analog Input Voltage Range V(+) or V(–)(3) GND–0.05 VCC+0.05 VDC

DC Common-Mode Error Over Analog Input Voltage Range ±1/16 ±1/8 LSB

VCC=5 VDC ±10% Over Allowed VIN(+) and VIN(–)

Power Supply Sensitivity ±1/16 ±1/8 LSB

Voltage Range(3)

(1) None of these ADCs requires a zero adjust (see Zero Error). To obtain zero code at other analog input voltages see Errors and

Reference Voltage Adjustments.

(2) The VREF/2 pin is the center point of a two-resistor divider connected from VCC to ground. In all versions of the ADC0801, ADC0802,

ADC0803, and ADC0805, and in the ADC0804LCJ, each resistor is typically 16 kΩ. In all versions of the ADC0804 except the

ADC0804LCJ, each resistor is typically 2.2 kΩ.

(3) For VIN(−)≥VIN(+) the digital output code will be 0000 0000. Two on-chip diodes are tied to each analog input (see block diagram)

which will forward conduct for analog input voltages one diode drop below ground or one diode drop greater than the VCC supply. Be

careful, during testing at low VCC levels (4.5V), as high level analog inputs (5V) can cause this input diode to conduct–especially at

elevated temperatures, and cause errors for analog inputs near full-scale. The spec allows 50 mV forward bias of either diode. This

means that as long as the analog VIN does not exceed the supply voltage by more than 50 mV, the output code will be correct. To

achieve an absolute 0 VDC to 5 VDC input voltage range will therefore require a minimum supply voltage of 4.950 VDC over temperature

variations, initial tolerance and loading.

6.7 AC Electrical Characteristics

The following specifications apply for VCC=5 VDC and TMIN≤TA≤TMAX (unless otherwise specified)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

fCLK = 640 kHz(1) 103 114 µs

TCConversion Time See (2)(1) 66 73 1/fCLK

Clock Frequency 100 640 1460 kHz

fCLK VCC = 5V(2)

Clock Duty Cycle 40% 60%

INTR tied to WR with CS = 0 VDC,

CR Conversion Rate in Free-Running Mode 8770 9708 conv/s

fCLK = 640 kHz

(1) Accuracy is specified at fCLK = 640 kHz. At higher clock frequencies accuracy can degrade. For lower clock frequencies, the duty cycle

limits can be extended so long as the minimum clock high time interval or minimum clock low time interval is no less than 275 ns.

(2) With an asynchronous start pulse, up to 8 clock periods may be required before the internal clock phases are proper to start the

conversion process. The start request is internally latched. Refer to Detailed Description.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

AC Electrical Characteristics (continued)

The following specifications apply for VCC=5 VDC and TMIN≤TA≤TMAX (unless otherwise specified)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

tW(WR) Width of WR Input (Start Pulse Width) CS = 0 VDC (3) 100

Access Time (Delay from Falling Edge of RD to

tACC CL= 100 pF 135 200

Output Data Valid) ns

t1H, Tri-State Control (Delay from Rising Edge of RD CL= 10 pF, RL= 10k (See Tri-State 125 200

t0H to Hi-Z State) Test Circuits and Waveforms)

Delay from Falling Edge of WR or RD to Reset

tWI, tRI 300 450

of INTR

CIN Input Capacitance of Logic Control Inputs 5 7.5 pF

COUT Tri-State Output Capacitance (Data Buffers) 5 7.5

CONTROL INPUTS [Note: CLK IN (Pin 4) is the input of a Schmitt trigger circuit and is therefore specified separately]

VIN (1) Logical “1” Input Voltage (Except Pin 4 CLK IN) VCC = 5.25 VDC 2 15 VDC

VIN (0) Logical “0” Input Voltage (Except Pin 4 CLK IN) VCC = 4.75 VDC 0.8

IIN (1) Logical “1” Input Current (All Inputs) VIN = 5 VDC 0.005 1 µADC

IIN (0) Logical “0” Input Current (All Inputs) VIN = 0 VDC –1 –0.005

CLOCK IN AND CLOCK R

VT+ CLK IN (Pin 4) Positive Going Threshold Voltage 2.7 3.1 3.5

CLK IN (Pin 4) Negative Going Threshold

VT−1.5 1.8 2.1

Voltage

VHCLK IN (Pin 4) Hysteresis (VT+)–(VT−) 0.6 1.3 2 VDC

VOUT Logical “0” CLK R Output Voltage IO= 360 µA, VCC = 4.75 VDC 0.4

(0)

VOUT Logical “1” CLK R Output Voltage IO=−360 µA, VCC = 4.75 VDC 2.4

(1)

DATA OUTPUTS AND INTR

Data Outputs IOUT = 1.6 mA, VCC = 4.75 VDC 0.4

VOUT Logical “0” Output

(0) Voltage INTR Output IOUT = 1.0 mA, VCC = 4.75 VDC 0.4 VDC

IO=−360 µA, VCC = 4.75 VDC 2.4

VOUT Logical “1” Output Voltage

(1) IO=−10 µA, VCC = 4.75 VDC 4.5

VOUT = 0 VDC –3

Tri-State Disabled Output Leakage (All Data

IOUT µADC

Buffers) VOUT = 5 VDC 3

ISOURC VOUT Short to GND, TA= 2 5°C 4.5 6

EmADC

ISINK VOUT Short to VCC, TA= 25°C 9 16

POWER SUPPLY

Supply Current ADC0801/02/03/04LCJ/05 1.1 1.8

fCLK = 640 kHz, VREF/2 = NC,

ICC (Includes Ladder mA

TA= 25°C and CS = 5 V

ADC0804LCN/LCWM 1.9 2.5

Current)

(3) The CS input is assumed to bracket the WR strobe input and therefore timing is dependent on the WR pulse width. An arbitrarily wide

pulse width will hold the converter in a reset mode and the start of conversion is initiated by the low to high transition of the WR pulse.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS sum canvznsmw WA. ‘7 ACNM. mmmu sums nr m nan \s vAun m Kmmuv [muss nnuvzam (lASY DATA wasnnn) 4. rme ‘L i x .7 ma ax mm ”mu nusv" J Immm 1,; 4. IV n (”51 mu was rm nsnm NOTE DATA _ _ OUTPUTS 9 ‘AIID .i K m! Asszamz 4. ‘k 1mm TRI~STATE “Hymn k

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Figure 1. Start Conversion

Note: Read strobe must occur 8 clock periods (8/fCLK) after assertion of interrupt to specify reset of INTR.

Figure 2. Output Enable and Reset With INTR

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

6.8 Typical Characteristics

Figure 4. Delay From Falling Edge of RD to Output Data

Figure 3. Logic Input Threshold Voltage vs Supply Voltage Valid vs Load Capacitance

Figure 5. CLK IN Schmitt Trip Levels vs Supply Voltage Figure 6. fCLK vs Clock Capacitor

Figure 7. Full-Scale Error vs Conversion Time Figure 8. Effect of Unadjusted Offset Error vs VREF/2 Voltage

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS numﬂ cunnim (mm svn nun numn auFrms a 'smmcz s Vow ‘ 1 ‘ Vnc *lsmx Vnuv '“Vn: 2 ,5“ 725 n 25 an 75 In" 125 v‘ 7 mama nwmnun: m IE 11 as I“ 4 inEn sumv cunnENr (wAncY I: ran 45 n in“ , mm E§=I 25 ill 15 ma 1, 7 mum nmmnmks r'c) uuunm EHKURHSIx.‘ n: \ x 1 w ‘ w x \ AIIEIIIIII wag/u , ‘1 I 3:7 S 156 7 V am» Ann mu- suLE nmusvsu)‘ ‘ ‘ ‘ ‘ I LSHVALUE Luv vmrzvamus w“)

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Typical Characteristics (continued)

Figure 10. Power Supply Current vs Temperature(1)

Figure 9. Output Current vs Temperature

Figure 11. Linearity Error at Low VREF/2 Voltages

(1) The VREF/2 pin is the center point of a two-resistor divider connected from VCC to ground. In all versions of the ADC0801, ADC0802,

ADC0803, and ADC0805, and in the ADC0804LCJ, each resistor is typically 16 kΩ. In all versions of the ADC0804 except the

ADC0804LCJ, each resistor is typically 2.2 kΩ.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS DATA OUTPUT q 1m 10k DATA OUTPUT 8L :L' GND DATA OUTPUTS GND DATA OUTPUTS VOL 10%

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

7 Parameter Measurement Information

7.1 Tri-State Test Circuits and Waveforms

CL= 10 pF

Figure 12. RD to Data Output Falling Edge Test Figure 13. RD to Data Output Falling Edge Test

Load Condition Timing

CL= 10 pF

Figure 14. RD to Data Output Rising Edge Test Figure 15. RD to Data Output Rising Edge Test

Load Condition Timing

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

8 Detailed Description

8.1 Overview

The ADC0801 series are versatile 8-Bit µP compatible general purpose ADC converters operate on single 5-V

supply. These devices are treated as a memory location or I/O port to a micro-processor system without

additional interface logic. The outputs are Tri-state latched which facilitate interfacing to micro-processor control

bus. The converter is designed with a differential potentiometric ladder, a circuit equivalent of the 256R network.

It contains analog switches sequenced by successive approximation logic. A functional diagram of the ADC

converter is shown in Functional Block Diagram. All of the package pinouts are shown and the major logic control

paths are drawn in heavier weight lines. The differential analog voltage input has good common mode-rejection

and permits offsetting the analog zero-input voltage value. Moreover, the input reference voltage can be adjusted

to allow encoding small analog voltage span to the full 8-bits resolution. To ensure start-up under all possible

conditions, an external WR pulse is required during the first power-up cycle.

Using a SAR logic the most significant bit is tested first and after 8 comparisons (64 clock cycles) a digital 8-bit

binary code (1111 1111 = full-scale) is transferred to an output latch and then an interrupt is asserted (INTR

makes a high-to-low transition). A conversion in process can be interrupted by issuing a second start command.

The device may be operated in the free-running mode by connecting INTR to the WR input with CS=0.

On the high-to-low transition of the WR input the internal SAR latches and the shift register stages are reset. As

long as the CS input and WR input remain low, the ADC will remain in a reset state. Conversion will start from 1

to 8 clock periods after at least one of these inputs makes a low-to-high transition.

The converter is started by having CS and WR simultaneously low. This sets the start flip-flop (F/F) and the

resulting “1” level resets the 8-bit shift register, resets the Interrupt (INTR) F/F and inputs a “1” to the D flop,

F/F1, which is at the input end of the 8-bit shift register. Internal clock signals then transfer this “1” to the Q

output of F/F1. The AND gate, G1, combines this “1” output with a clock signal to provide a reset signal to the

start F/F. If the set signal is no longer present (either WR or CS is a “1”) the start F/F is reset and the 8-bit shift

present, this reset pulse would have no effect (both outputs of the start F/F would momentarily be at a “1” level)

and the 8-bit shift register would continue to be held in the reset mode. This logic therefore allows for wide CS

and WR signals and the converter will start after at least one of these signals returns high and the internal clocks

again provide a reset signal for the start F/F.

After the “1” is clocked through the 8-bit shift register (which completes the SAR search) it appears as the input

to the D-type latch, LATCH 1. As soon as this “1” is output from the shift register, the AND gate, G2, causes the

new digital word to transfer to the Tri-state output latches. When LATCH 1 is subsequently enabled, the Q output

makes a high-to-low transition which causes the INTR F/F to set. An inverting buffer then supplies the INTR input

signal.

Note this SET control of the INTR F/F remains low for 8 of the external clock periods (as the internal clocks run

at 1/8 of the frequency of the external clock). If the data output is continuously enabled (CS and RD both held

low), the INTR output will still signal the end of conversion (by a high-to-low transition), because the SET input

can control the Q output of the INTR F/F even though the RESET input is constantly at a M "1M " level in this

operating mode. This INTR output will therefore stay low for the duration of the SET signal, which is 8 periods of

the external clock frequency (assuming the ADC is not started during this interval).

When operating in the free-running or continuous conversion mode (INTR pin tied to WR and CS wired low – see

Continuous Conversions), the START F/F is SET by the high-to-low transition of the INTR signal. This resets the

SHIFT REGISTER which causes the input to the D-type latch, LATCH 1, to go low. As the latch enable input is

still present, the Q output will go high, which then allows the INTR F/F to be RESET. This reduces the width of

the resulting INTR output pulse to only a few propagation delays (approximately 300 ns).

When data is to be read, the combination of both CS and RD being low will cause the INTR F/F to be reset and

the Tri-state output latches will be enabled to provide the 8-bit digital outputs.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

v «Essnmwﬁﬁnmm 'n -ausv Aunnulzscwrsnvz l TEXAS INSTRUMENTS H in a MED ., ““1 M. n Vcc 'VIEH x nzcuum mmzn ammo: “is" I Vlmm d‘ .M ”W "“L L A A $ J, J, A“ i—n— W L'Emm u mum Emu! nzszr

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

8.2 Functional Block Diagram

(1) CS shown twice for clarity.

(2) SAR = Successive Approximation Register.

8.3 Feature Description

8.3.1 Understanding ADC Error Specs

A perfect ADC transfer characteristic (staircase waveform) is shown in Figure 16 and Figure 17. The horizontal

scale is analog input voltage and the particular points labeled are in steps of 1 LSB (19.53 mV with 2.5V tied to

the VREF/2 pin). The digital output codes that correspond to these inputs are shown as D−1, D, and D+1. For

the perfect ADC, not only will center- value (A−1, A, A+1, . . . . ) analog inputs produce the cor- rect output digital

codes, but also each riser (the transitions between adjacent output codes) will be located ±1⁄2 LSB away from

each center-value. As shown, the risers are ideal and have no width. Correct digital output codes will be provided

for a range of analog input voltages that extend ±1⁄2 LSB from the ideal center-values. Each tread (the range of

analog input voltage that provides the same digital output code) is therefore 1 LSB wide.

Figure 19 shows a worst case error plot for the ADC0801. All center-valued inputs are guaranteed to produce the

correct output codes and the adjacent risers are specified to be no closer to the center-value points than ±1/4

LSB. In other words, if we apply an analog input equal to the center-value ±1/4 LSB, we guarantee that the ADC

will produce the correct digital code. The maximum range of the position of the code transition is indicated by the

horizontal arrow and it is specified to be no more than 1/2 LSB.

The error curve of Figure 21 shows a worst case error plot for the ADC0802. Here we guarantee that if we apply

an analog input equal to the LSB analog voltage center-value the ADC will produce the correct digital code.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS DIEITAL uuTPuTcDDE a . A71 A n+1 AMALDEINPUTIVIN) vl 183 01/2 [55 mnnn *I/Z [SB 7| LSB mums mPuT 1va nlnlrnlnnrrurcant A’I A An ANALIIE mm mm .1 L5! m: m .m m sum rm m m m 4 m mum mmnvwr mmm mum cnuE nu Amunu mm mm u m Ennnk VI un AA A m mums mmww)

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Feature Description (continued)

Next to each transfer function is shown the corresponding error plot. Many people may be more familiar with

error plots than transfer functions. The analog input voltage to the ADC is provided by either a linear ramp or by

the discrete output steps of a high resolution DAC. Notice that the error is continuously displayed and includes

the quantization uncertainty of the ADC. For example the error at point 1 of Figure 21 is +1⁄2 LSB because the

digital code appeared 1⁄2 LSB in advance of the center-value of the tread. The error plots always have a

constant negative slope and the abrupt up-side steps are always 1 LSB in magnitude.

Figure 17. Clarifying the Error Specs of an ADC Converter

Figure 16. Transfer Function of Analog Input vs Digital Accuracy=±0 LSB: A Perfect ADC

Output Code in Ideal ADC

Figure 18. Transfer Function of Analog Input vs Digital Figure 19. Clarifying the Error Specs of an ADC Converter

Output Code for ±1/4 LSB Accuracy ADC Accuracy =±1⁄4 LSB

Figure 20. Transfer Function of Analog Input vs Digital Figure 21. Clarifying the Error Specs of an ADC Converter

Output Code for ±1/2 LSB Accuracy ADC Accuracy = ±1⁄2 LSB

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS Rs 'CHARGE 5 'Im

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Feature Description (continued)

8.3.2 Digital Control Inputs

The digital control inputs (CS, RD, and WR) meet standard TLL logic voltage levels. These signals have been

renamed when compared to the standard ADC Start and Output Enable labels. In addition, these inputs are

active low to allow an easy interface to microprocessor control busses. For non-microprocessor based

applications, the CS input (pin 1) can be grounded and the standard ADC Start function is obtained by an active

low pulse applied at the WR input (pin 3) and the Output Enable function is caused by an active low pull at the

RD input (pin 2).

8.4 Device Functional Modes

8.4.1 Analog Input Modes

8.4.1.1 Normal Mode

Due to the internal switching action, displacement currents will flow at the analog inputs. This is due to on-chip

stray capacitance to ground as shown in Figure 22.

rON of SW 1 and SW 2.5 kΩ

r=rON CSTRAY × 5 kΩx 12 pF = 60 ns

Figure 22. Analog Input Impedance

The voltage on this capacitance is switched and will result in currents entering the VIN(+) input pin and leaving

the VIN(−) input which will depend on the analog differential input voltage levels. These current transients occur

at the leading edge of the internal clocks. They rapidly decay and do not cause errors as the on-chip comparator

is strobed at the end of the clock period.

8.4.1.2 Fault Mode

If the voltage source applied to the VIN(+) or VIN(−) pin exceeds the allowed operating range of VCC+50 mV, large

input currents can flow through a parasitic diode to the VCC pin. If these currents can exceed the 1 mA max

allowed spec, an external diode (1N914) should be added to bypass this current to the VCC pin (with the current

bypassed with this diode, the voltage at the VIN(+) pin can exceed the VCC voltage by the forward voltage of this

diode).

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

9.1 Application Information

The following sections give example circuits and suggestions for using the ADC080X in typical application

situation with a typical 8-bit micro-processor.

9.1.1 Testing the ADC Converter

There are many degrees of complexity associated with testing an ADC converter. One of the simplest tests is to

apply a known analog input voltage to the converter and use LEDs to display the resulting digital output code as

shown in Figure 23.

For ease of testing, the VREF/2 (pin 9) should be supplied with 2.560 VDC and a VCC supply voltage of 5.12 VDC

should be used. This provides an LSB value of 20 mV.

If a full-scale adjustment is to be made, an analog input voltage of 5.090 VDC (5.120–1/⁄2 LSB) should be applied

to the VIN(+) pin with the VIN(−) pin grounded. The value of the VREF/2 input voltage should then be adjusted until

the digital output code is just changing from 1111 1110 to 1111 1111. This value of VREF/2 should then be used

for all the tests.

The digital output LED display can be decoded by dividing the 8 bits into 2 hex characters, the 4 most significant

(MS) and the 4 least significant (LS). Table 1 shows the fractional binary equivalent of these two 4-bit groups. By

adding the voltages obtained from the "VM" and "VLS" columns in Table 1, the nominal value of the digital

display (when VREF/2 = 2.560V) can be determined. For example, for an output LED display of 1011 0110 or B6

(in hex), the voltage values from the table are 3.520 + 0.120 or 3.640 VDC. These voltage values represent the

center-values of a perfect ADC converter. The effects of quantization error have to be accounted for in the

interpretation of the test results.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS m I50 pF V 1" :0 stuvm ”‘7 + “Inf .9 ; :YANIMUM ,. L5! 17 sum m éé A/D 15 mar 5v”: 7 I J AEND 2 $4? m usL5u27 {ID

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Application Information (continued)

Figure 23. Basic ADC Tester

For a higher speed test system, or to obtain plotted data, a digital-to-analog converter is needed for the test set-

up. An accurate 10-bit DAC can serve as the precision voltage source for the ADC. Errors of the ADC under test

can be expressed as either analog voltages or differences in 2 digital words.

A basic ADC tester that uses a DAC and provides the error as an analog output voltage is shown in Figure 35.

The 2 op amps can be eliminated if a lab DVM with a numerical subtraction feature is available to read the

difference voltage, "A–C", directly. The analog input voltage can be supplied by a low frequency ramp generator

and an X-Y plotter can be used to provide analog error (Y axis) versus analog input (X axis).

For operation with a microprocessor or a computer-based test system, it is more convenient to present the errors

digitally. This can be done with the circuit of Figure 25, where the output code transitions can be detected as the

10-bit DAC is incremented. This provides 1⁄4 LSB steps for the 8-bit ADC under test. If the results of this test are

automatically plotted with the analog input on the X axis and the error (in LSB’s) as the Y axis, a useful transfer

function of the ADC under test results. For acceptance testing, the plot is not necessary and the testing speed

can be increased by establishing internal limits on the allowed error for each code.

9.1.2 Microprocessor Interfacing

To discuss the interface with 8080A and 6800 microprocessors, a common sample subroutine structure is used.

The microprocessor starts the ADC, reads and stores the results of 16 successive conversions, then returns to

the user’s program. The 16 data bytes are stored in 16 successive memory locations. All Data and Addresses

will be given in hexadecimal form. Software and hardware details are provided separately for each type of

microprocessor.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS 3.5.7 DAC1I1l10 A/D man VANALUG OUTPUT UNDER 1st DAC ANALOG INPUT VOLTAGE ‘lﬂDX ANALUE ERROR VUlTAEE v DIGITAL "“1“” ANALOG A/D UNDER DIGITAL 1043” INPUT DAC TEST OUTPUT

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Application Information (continued)

9.1.2.1 Interfacing 8080 Microprocessor Derivatives (8048, 8085)

This converter has been designed to directly interface with derivatives of the 8080 microprocessor. The ADC can

be mapped into memory space (using standard memory address decoding for CS and the MEMR and MEMW

strobes) or it can be controlled as an I/O device by using the I/O R and I/O W strobes and decoding the address

bits A0 →A7 (or address bits A8 →A15 as they will contain the same 8-bit address information) to obtain the

CS input. Using the I/O space provides 256 additional addresses and may allow a simpler 8-bit address decoder

but the data can only be input to the accumulator. To make use of the additional memory reference instructions,

the ADC should be mapped into memory space. An example of an ADC in I/O space is shown in Figure 26.

Figure 24. ADC Tester with Analog Error Output

Figure 25. Basic “Digital” ADC Tester

Table 1. Decoding the Digital Output LEDs

OUTPUT VOLTAGE CENTER VALUES

FRACTIONAL BINARY VALUE FOR WITH VREF/2=2.560 VDC

HEX BINARY

MS GROUP LS GROUP VMS GROUP(1) VLS GROUP(1)

F 1 1 1 1 15/16 15/256 4.800 0.300

E 1 1 1 0 7/8 7/128 4.480 0.280

D 1 1 0 1 13/16 13/256 4.160 0.260

C 1 1 0 0 3/4 3/64 3.840 0.240

B 1 0 1 1 11/16 11/256 3.520 0.220

(1) Display Output=VMS Group + VLS Group

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS m n.‘ m: m nu- mm \m' Tum ' nmm‘ umm‘ num)’ nmsx‘ may“ uuulv nairzn)‘ num- .u.‘uu mm: ms us! An" u!) AW! 4m mam m cumuumn Mm (m um um Anmm

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Application Information (continued)

Table 1. Decoding the Digital Output LEDs (continued)

OUTPUT VOLTAGE CENTER VALUES

FRACTIONAL BINARY VALUE FOR WITH VREF/2=2.560 VDC

HEX BINARY

MS GROUP LS GROUP VMS GROUP(1) VLS GROUP(1)

A 1 0 1 0 5/8 5/128 3.200 0.200

9 1 0 0 1 9/16 9/256 2.880 0.180

8 1 0 0 0 1/2 1/32 2.560 0.160

7 0 1 1 1 7/16 7/256 2.240 0.140

6 0 1 1 0 3/8 3/128 1.920 0.120

5 0 1 0 1 5/16 2/256 1.600 0.100

4 0 1 0 0 1/4 1/64 1.280 0.080

3 0 0 1 1 163 3/256 0.960 0.060

2 0 0 1 0 1/8 1/128 0.640 0.040

1 0 0 0 1 1/16 1/256 0.320 0.020

0 0 0 0 0 0 0

(1) *Pin numbers for the DP8228 system controller, others are INS8080A

(2) Pin 23 of the INS8228 must be tied to +12V through a 1 kΩresistor to generate the RST 7 instruction when an

interrupt is acknowledged as required by the accompanying sample program.

Figure 26. ADC0801_INS8080A CPU Interface

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS 0038 03 00 03 EST 7 : JMP Ll! DATA . . . . . . 0100 21 00 02 START: LXIHOZOOH :HL palrwillpoinv. to :data storag: lam-nuns 0103 31 00 U4 RETURN: LXI SF 0400!! :Inniali ze slack pointer (Note 1) 0106 7D NOVA, I: :Test#ofbytes entered 0107 F20? CPIOFH :If#:lS.JM'Pco 0109 CA 1301. JZ CONT :usorprogram 01°C 03 E0 OUT E0 H :Slart A/D 010E F}! El :Enabla Interrupt 01017 00 LDOP: NDP :Laapunlil and of 0110 C3 0F 01 JMPLODF ;canvnrsion 0113 ' CONT : ‘ . . . . a - (User program to . - - process data) - . . . . . . . . 0300 DB 20 1-D DATA: INEOH :Luad data in” accumulatcr 0302 77 MOVM, A :57.ch data 0503 23 “IX H ; Increment slurage puimar 0304 C3 03 01 JMPRETURN

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Note: The stack pointer must be dimensioned because a RST 7 instruction pushes the PC onto the stack.

Note: All address used were arbitrarily chosen.

Figure 27. Sample Program for Figure 26 ADC0801–INS8080A CPU Interface

The standard control bus signals of the 8080 CS, RD and WR) can be directly wired to the digital control inputs

of the ADC and the bus timing requirements are met to allow both starting the converter and outputting the data

onto the data bus. A bus driver should be used for larger microprocessor systems where the data bus leaves the

PCB and/or must drive capacitive loads larger than 100 pF.

9.1.2.2 Sample 8080A CPU Interfacing Circuitry and Program

The following sample program and associated hardware shown in Figure 26 may be used to input data from the

converter to the INS8080A CPU chip set (comprised of the INS8080A microprocessor, the INS8228 system

controller and the INS8224 clock generator). For simplicity, the ADC is controlled as an I/O device, specifically an

8-bit bi-directional port located at an arbitrarily chosen port address, E0. The Tri-state output capability of the

ADC eliminates the need for a peripheral interface device, however address decoding is still required to generate

the appropriate CS for the converter.

It is important to note in systems where the ADC converter is 1-of-8 or less I/O mapped devices, no address

decoding circuitry is necessary. Each of the 8 address bits (A0 to A7) can be directly used as CS inputs — one

for each I/O device.

9.1.2.3 INS8048 Interface

The INS8048 interface technique with the ADC0801 series (see Figure 28) is simpler than the 8080A CPU

interface. There are 24 I/O lines and three test input lines in the 8048. With these extra I/O lines available, one of

the I/O lines (bit 0 of port 1) is used as the chip select signal to the ADC, thus eliminating the use of an external

address decoder. Bus control signals RD, WR and INT of the 8048 are tied directly to the ADC. The 16

converted data words are stored at on-chip RAM locations from 20 to 2F (Hex). The RD and WR signals are

generated by reading from and writing into a dummy address, respectively. A sample interface program is shown

below.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS 04 10 04 50 99 PE 51 89 01 BB 20 B9 FF BA 10 25 PF 99 FE 91 05 96 21 EA 1): 00 00 31 A0 18 59 01 27 95 an Z“ V” nan '2 ‘8 nan V“ m“ 4'3—J M1 2 ma! ‘H—IG an: m 4‘5—‘5 1m Dan 4—” “ mu m H mm m H “as Ins-w nn “9—" an Ann-am — u _ RD ——> Rn ClK R In 7 WI»? ——> M M m W H a VI" A 5ND In D END d Vss = START: AGAIN: LOOP: XNDATA: JM‘F ORG 1MP ORG ANL Movx ORL MOV Mov Muv Mov ANL Movx EN JNZ DJNZ N0? NUP ORG anx Mov INC ORL CLR RETR 10H :59 508 10H P1. #OFEH A, @Rl P1, t1 no, #20“ nu. wow-1 R2. #10}: A. ”01“?“ P1. «om-1 mu, A I L00? R2. AGAHI 50H A. @m @xo, A R0 Fl , #1 A :Yragram starts av. addr 10 :lnlarruptjumpvsctor :Maxn program :cmp salect :xsadxnma )5! mm: :La rssn the inn- :Set pox-L plnhigh CD313 addrass : Dummy address :Caumer tar 16 bytes 81 ACC far incr loep and cs (Ian 0 afPl) andWRout nabla xnurrupt :wnL {urlntarrupt :1: 15 bytas are Mad :3n n: user'spragram 'lnpul data. as sun low :sure inmemGY’Y :Incramenl storaga counter ass! as signal ,c1sar ACC us get nut at :me interrupt loop

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Figure 28. INS8048 Interface

Figure 29. Sample Program for Figure 28 INS8048 Interface

9.1.2.4 Interfacing the Z-80

The Z-80 control bus is slightly different from that of the 8080. General RD and WR strobes are provided and

separate memory request, MREQ, and I/O request, IORQ, signals are used which have to be combined with the

generalized strobes to provide the equivalent 8080 signals. An advantage of operating the ADC in I/O space with

the Z-80 is that the CPU will automatically insert one wait state (the RD and WR strobes are extended one clock

period) to allow more time for the I/O devices to respond. Logic to map the ADC in I/O space is shown in

Figure 30.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS MM74C32

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Figure 30. Mapping the ADC as an I/O Device for Use With the Z-80 CPU

Additional I/O advantages exist as software DMA routines are available and use can be made of the output data

transfer which exists on the upper 8 address lines (A8 to A15) during I/O input instructions. For example, MUX

channel selection for the ADC can be accomplished with this operating mode.

9.1.2.5 Interfacing 6800 Microprocessor Derivatives (6502, etc.)

The control bus for the 6800 microprocessor derivatives does not use the RD and WR strobe signals. Instead it

employs a single R/W line and additional timing, if needed, can be derived from the φ2 clock. All I/O devices are

memory mapped in the 6800 system, and a special signal, VMA, indicates that the current address is valid.

Figure 36 shows an interface schematic where the ADC is memory mapped in the 6800 system. For simplicity,

the CS decoding is shown using 1/2 DM8092. Note in many 6800 systems, an already decoded 4/5 line is

brought out to the common bus at pin 21. This can be tied directly to the CS pin of the ADC, provided that no

other devices are addressed at HX ADDR: 4XXX or 5XXX.

The following subroutine performs essentially the same function as in the case of the 8080A interface and it can

be called from anywhere in the user’s program.

In Figure 38 the ADC0801 series is interfaced to the M6800 microprocessor through (the arbitrarily chosen) Port

B of the MC6820 or MC6821 Peripheral Interface Adapter, (PIA).

Here the CS pin of the ADC is grounded because the PIA is already memory mapped in the M6800 system and

no CS decoding is necessary. Also notice that the ADC output data lines are connected to the microprocessor

bus under program control through the PIA and therefore the ADC RD pin can be grounded.

A sample interface program equivalent to the previous one is shown below Figure 38. The PIA Data and Control

Registers of Port B are located at HEX addresses 8006 and 8007, respectively.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS ‘ , an _.'onn —v‘om 4—2: W " an m 2 '1 m mum. : n W w 1 u nu ” all ’ ” m? a mum u "ml—oxiislcrmrl 7 u [m u I" m awn? CS —§° m) __pq NSCBDU. all“, —wn ——>OI lel, 8048. ETC. ¥ musunm unlisnwrmn nvtnnvuismﬂ Amnnslum unnnnnlm xmsumum DATA A/D

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

9.2 Typical Applications

9.2.1 8080 Interface

Figure 31. Generic Interface Between ADC and 8-Bit µPs

ERROR SPECIFICATION (Includes Full-Scale, Zero Error, and Non-Linearity)

VREF/2 = 2.500 VDC VREF/2 = No Connection

FULL-SCALE

PART NUMBER ADJUSTED (No Adjustments) (No Adjustments)

ADC0801 ±1⁄4 LSB

ADC0802 ±1⁄2 LSB

ADC0803 ±1⁄2 LSB

ADC0804 ±1 LSB

ADC0805 ±1 LSB

9.2.1.1 Design Requirements

For these example applications, the input analog signal is differential to illustrate the offset and common mode

reduction merits. An example of the use of an adjusted reference voltage is to accommodate a reduced span or

dynamic voltage range of the analog input voltage is also depicted.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS ' 4.5 ' MW. : (vpnznfm) H‘ v 7[Ave1MAX)(fCLK):| F ’ (21:10,“)(45) VP :(5x10’3n540x103) (seaxeow 5)

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Table 2. Design Parameters

PARAMETER EXAMPLE VALUE

ADC clock frequency, FCLK 640 KHz

Input source resistance, RIN 100 Ω

9.2.1.2 Detailed Design Procedure

9.2.1.2.1 Analog Differential Voltage Inputs and Common-Mode Rejection

This ADC has additional applications flexibility due to the analog differential voltage input. The VIN(−) input (pin 7)

can be used to automatically subtract a fixed voltage value from the input reading (tare correction). This is also

useful in 4 mA–20 mA current loop conversion. In addition, common-mode noise can be reduced by use of the

differential input.

The time interval between sampling VIN(+) and VIN(−) is 4-1/2 clock periods. The maximum error voltage due to

this slight time difference between the input voltage samples is given by:

where

•∆Veis the error voltage due to sampling delay

• VPis the peak value of the common-mode voltage

• fcm is the common-mode frequency (1)

As an example, to keep this error to 1/4 LSB (∼5 mV) when operating with a 60 Hz common-mode frequency,

fcm, and using a 640 kHz ADC clock, fCLK, would allow a peak value of the common-mode voltage, VP, which is

given by:

(2)

(3)

which gives VP–1.9 V.

The allowed range of analog input voltages usually places more severe restrictions on input common-mode noise

levels.

An analog input voltage with a reduced span and a relatively large zero offset can be handled easily by making

use of the differential input (see Reference Voltage).

9.2.1.2.2 Analog Inputs — Input Current

9.2.1.2.2.1 Input Bypass Capacitors

Bypass capacitors at the inputs will average these charges and cause a DC current to flow through the output

resistances of the analog signal sources. This charge pumping action is worse for continuous conversions with

the VIN(+) input voltage at full-scale. For continuous conversions with a 640 kHz clock frequency with the VIN(+)

input at 5V, this DC current is at a maximum of approximately 5 µA. Therefore, bypass capacitors should not be

used at the analog inputs or the VREF/2 pin for high resistance sources (> 1 kΩ). If input bypass capacitors are

necessary for noise filtering and high source resistance is desirable to minimize capacitor size, the detrimental

effects of the voltage drop across this input resistance, which is due to the average value of the input current,

can be eliminated with a full-scale adjustment while the given source resistor and input bypass capacitor are both

in place. This is possible because the average value of the input current is a precise linear function of the

differential input voltage.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS VcclVRErY Tu ! VREF/IO— a DIGITAL I CIRCUITS l ANALOG R l nzcun: CIRCUITS AGﬂlJ In BEND In _ I77

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

9.2.1.2.2.2 Input Source Resistance

Large values of source resistance where an input bypass capacitor is not used, will not cause errors as the input

currents settle out prior to the comparison time. If a low pass filter is required in the system, use a low valued

series resistor (≤1 kΩ) for a passive RC section or add an op amp RC active low pass filter. For low source

resistance applications, (≤1 kΩ), a 0.1 μF bypass capacitor at the inputs will prevent noise pickup due to series

lead inductance of a long wire. A 100Ωseries resistor can be used to isolate this capacitor — both the R and C

are placed outside the feedback loop — from the output of an op amp, if used.

9.2.1.2.2.3 Noise

The leads to the analog inputs (pins 6 and 7) should be kept as short as possible to minimize input noise

coupling. Both noise and undesired digital clock coupling to these inputs can cause system errors. The source

resistance for these inputs should, in general, be kept below 5 kΩ. Larger values of source resistance can cause

undesired system noise pickup. Input bypass capacitors, placed from the analog inputs to ground, will eliminate

system noise pickup but can create analog scale errors as these capacitors will average the transient input

switching currents of the ADC (see Analog Inputs — Input Current). This scale error depends on both a large

source resistance and the use of an input bypass capacitor. This error can be eliminated by doing a full-scale

adjustment of the ADC (adjust VREF/2 for a proper full-scale reading — see Full-Scale) with the source resistance

and input bypass capacitor in place.

Noise spikes on the VCC supply line can cause conversion errors as the comparator will respond to this noise. A

low inductance tantalum filter capacitor should be used close to the converter VCC pin and values of 1 µF or

greater are recommended. If an unregulated voltage is available in the system, a separate LM340LAZ-5.0, TO-

92, 5-V voltage regulator for the converter (and other analog circuitry) will greatly reduce digital noise on the VCC

supply.

9.2.1.2.3 Reference Voltage

9.2.1.2.3.1 Span Adjust

For maximum applications flexibility, these ADCs have been designed to accommodate a 5 VDC, 2.5 VDC or an

adjusted voltage reference. This has been achieved in the design of the IC as shown in Figure 32.

Figure 32. The VREFERENCE Design on the IC

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS - 5" V|N(+)MAX + E 4 (3.5V) ; 3 ¥ 2 Vm(+)MIN SPAN=3V 1 (0.5V) { a

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Notice that the reference voltage for the IC is either 1/2 of the voltage applied to the VCC supply pin, or is equal to

the voltage that is externally forced at the VREF/2 pin. This allows for a ratiometric voltage reference using the

VCC supply, a 5 VDC reference voltage can be used for the VCC supply or a voltage less than 2.5 VDC can be

applied to the VREF/2 input for increased application flexibility. The internal gain to the VREF/2 input is 2, making

the full-scale differential input voltage twice the voltage at pin 9.

An example of the use of an adjusted reference voltage is to accommodate a reduced span — or dynamic

voltage range of the analog input voltage. If the analog input voltage were to range from 0.5 VDC to 3.5 VDC,

instead of 0V to 5 VDC, the span would be 3 V as shown in Figure 33. With 0.5 VDC applied to the VIN(−) pin to

absorb the offset, the reference voltage can be made equal to 1/2 of the 3V span or 1.5 VDC. The ADC now will

encode the VIN(+) signal from 0.5V to 3.5 V with the 0.5V input corresponding to zero and the 3.5 VDC input

corresponding to full-scale. The full 8 bits of resolution are therefore applied over this reduced analog input

voltage range.

9.2.1.2.3.2 Reference Accuracy Requirements

The converter can be operated in a ratiometric mode or an absolute mode. In ratiometric converter applications,

the magnitude of the reference voltage is a factor in both the output of the source transducer and the output of

the ADC converter and therefore cancels out in the final digital output code. The ADC0805 is specified

particularly for use in ratiometric applications with no adjustments required. In absolute conversion applications,

both the initial value and the temperature stability of the reference voltage are important factors in the accuracy

of the ADC converter. For VREF/2 voltages of 2.4 VDC nominal value, initial errors of ±10 mVDC will cause

conversion errors of ±1 LSB due to the gain of 2 of the VREF/2 input. In reduced span applications, the initial

value and the stability of the VREF/2 input voltage become even more important. For example, if the span is

reduced to 2.5 V, the analog input LSB voltage value is correspondingly reduced from 20 mV (5V span) to 10 mV

and 1 LSB at the VREF/2 input becomes 5 mV. As can be seen, this reduces the allowed initial tolerance of the

reference voltage and requires correspondingly less absolute change with temperature variations. Note that

spans smaller than 2.5 V place even tighter requirements on the initial accuracy and stability of the reference

source.

In general, the magnitude of the reference voltage will require an initial adjustment. Errors due to an improper

value of reference voltage appear as full-scale errors in the ADC transfer function. IC voltage regulators may be

used for references if the ambient temperature changes are not excessive. The LM336B 2.5-V IC reference

diode (from National Semiconductor) has a temperature stability of 1.8 mV typical (6 mV maximum) over

0°C≤TA≤+70°C. Other temperature range parts are also available.

Figure 33. Analog Input Signal Example

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS s 0— mm) 9 All] VnEr/Z 7 va *VHEF SPAN/Z luv“) ‘— u.5vuc 1.5ch 1 . ZEHD-SHlFY SPAN 12 mm R ADJ ADJ

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

*Add if VREF/2 ≤1 VDC with LM358 to draw 3 mA to ground.

Figure 34. Accommodating an Analog Input from 0.5V (Digital Out = 00HEX) to 3.5 V (Digital Out=FFHEX)

9.2.1.2.4 Errors and Reference Voltage Adjustments

9.2.1.2.4.1 Zero Error

The zero of the ADC does not require adjustment. If the minimum analog input voltage value, VIN(MIN), is not

ground, a zero offset can be done. The converter can be made to output 0000 0000 digital code for this minimum

input voltage by biasing the ADC VIN(−) input at this VIN(MIN) value (see Application Information). This uses the

differential mode operation of the ADC.

The zero error of the ADC converter relates to the location of the first riser of the transfer function and can be

measured by grounding the VIN(−) input and applying a small magnitude positive voltage to the VIN(+) input. Zero

error is the difference between the actual DC input voltage that is necessary to just cause an output digital code

transition from 0000 0000 to 0000 0001 and the ideal 1/2 LSB value (1/2 LSB = 9.8 mV for VREF/2=2.500 VDC).

9.2.1.2.4.2 Full-Scale

The full-scale adjustment can be made by applying a differential input voltage that is 11/2 LSB less than the

desired analog full-scale voltage range and then adjusting the magnitude of the VREF/2 input (pin 9 or the VCC

supply if pin 9 is not used) for a digital output code that is just changing from 1111 1110 to 1111 1111.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS (VMAXWMIN) V (sad :V 15 7 MM J M 256 ‘ N m CLK R 19 m m K 4 CL A/D

- +

+ -

=é ù

æ öæ ö

ê ú

ç ÷ç ÷

ê ú

è øè ø

ë û

CLK

CC T T

V V V

RC ln

V V V

R 10 kΩ

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

9.2.1.2.4.3 Adjusting for an Arbitrary Analog Input Voltage Range

If the analog zero voltage of the ADC is shifted away from ground (for example, to accommodate an analog input

signal that does not go to ground) this new zero reference should be properly adjusted first. A VIN(+) voltage that

equals this desired zero reference plus 1/2 LSB (where the LSB is calculated for the desired analog span, 1

LSB=analog span/256) is applied to pin 6 and the zero reference voltage at pin 7 should then be adjusted to just

obtain the 00HEX to 01HEX code transition.

The full-scale adjustment should then be made (with the proper VIN(−) voltage applied) by forcing a voltage to the

VIN(+) input which is given by:

where

• VMAX = The high end of the analog input range

• VMIN = the low end (the offset zero) of the analog range. (Both are ground referenced.) (4)

The VREF/2 (or VCC) voltage is then adjusted to provide a code change from FEHEX to FFHEX. This completes the

adjustment procedure

9.2.1.2.5 Clocking Option

The clock for the ADC can be derived from the CPU clock or an external RC can be added to provide self-

clocking. The CLK IN (pin 4) makes use of a Schmitt trigger as shown in Figure 35.

Figure 35. Self-Clocking the ADC

Heavy capacitive or DC loading of the clock R pin should be avoided as this will disturb normal converter

operation. Loads less than 50 pF, such as driving up to 7 ADC converter clock inputs from a single clock R pin of

1 converter, are allowed. For larger clock line loading, a CMOS or low power TTL buffer or PNP input logic

should be used to minimize the loading on the clock R pin (do not use a standard TTL buffer).

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

9.2.1.2.6 Restart During a Conversion

If the ADC is restarted (CS and WR go low and return high) during a conversion, the converter is reset and a

new conversion is started. The output data latch is not updated if the conversion in process is not allowed to be

completed, therefore the data of the previous conversion remains in this latch. The INTR output simply remains

at the “1” level.

9.2.1.2.7 Continuous Conversions

For operation in the free-running mode an initializing pulse should be used, following power up, to ensure circuit

operation. In this application, the CS input is grounded and the WR input is tied to the INTR output. This WR and

INTR node should be momentarily forced to logic low following a power-up cycle to ensure operation.

9.2.1.2.8 Driving the Data Bus

This MOS ADC, like MOS microprocessors and memories, will require a bus driver when the total capacitance of

the data bus gets large. Other circuitry, which is tied to the data bus, will add to the total capacitive loading, even

in Tri-state (high impedance mode). Backplane bussing also greatly adds to the stray capacitance of the data

bus.

There are some alternatives available to the designer to handle this problem. Basically, the capacitive loading of

the data bus slows down the response time, even though DC specifications are still met. For systems operating

with a relatively slow CPU clock frequency, more time is available in which to establish proper logic levels on the

bus and therefore higher capacitive loads can be driven (see typical characteristics curves).

At higher CPU clock frequencies time can be extended for I/O reads (and/or writes) by inserting wait states

(8080) or using clock extending circuits (6800).

Finally, if time is short and capacitive loading is high, external bus drivers must be used. These can be Tri-state

buffers (low power Schottky such as the DM74LS240 series is recommended) or special higher drive current

products which are designed as bus drivers. High current bipolar bus drivers with PNP inputs are recommended.

9.2.1.2.9 Wiring and Hook-Up Precautions

Standard digital wire wrap sockets are not satisfactory for breadboarding this ADC converter. Sockets on PCBs

can be used and all logic signal wires and leads should be grouped and kept as far away as possible from the

analog signal leads. Exposed leads to the analog inputs can cause undesired digital noise and hum pickup,

therefore shielded leads may be necessary in many applications.

A single point analog ground that is separate from the logic ground points should be used. The power supply

bypass capacitor and the self-clocking capacitor (if used) should both be returned to digital ground. Any VREF/2

bypass capacitors, analog input filter capacitors, or input signal shielding should be returned to the analog

ground point. A test for proper grounding is to measure the zero error of the ADC converter. Zero errors in

excess of 1/4 LSB can usually be traced to improper board layout and wiring (see Zero Error for measuring the

zero error).

9.2.2 Multiple ADC0801 Series to MC6800 CPU Interface

To transfer analog data from several channels to a single microprocessor system, a multiple converter scheme

presents several advantages over the conventional multiplexer single-converter approach. With the ADC0801

series, the differential inputs allow individual span adjustment for each channel. Furthermore, all analog input

channels are sensed simultaneously, which essentially divides the total system servicing time of the

microprocessor by the number of channels, because all conversions occur simultaneously. This scheme is

shown in Figure 40.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS Wuﬂnl" WW Y!“ [El * Tm; ' W m “‘2': an (m .m m 412} [m In an m ANALIIE n! um [i] mm: In my um [75 In) um 05 m) m 01 um [I] m m) m: m my my 5 m (w M ”1 anlz A15 A25) [:1] WM (5) W limm In, W)? V 41 AM: 0010 DP 36 1mm" srx mum :Snva {mutants orx 0012 CE 00 2c LDX #30020 :Uponﬁ low CPU 0015 FF PF 125 srx mm; nmps w 0020 0015 57 50 on sun 35000 .smrt ADCOBDI 0013 0: cm ooxc 312 comm- wu :wmz m- incsrrupt oom DE 34 LDX man om as 02 0F m #3020! :15 mm data stared? 0022 27 14 mm END? 0024 37 50 no sun 35000 :ReslarcsADCOBOl 0027 05 In 0028 m? 34 Six mm 002A 20 yo mm comm ooze DE 34 INTRFT LDX mam 0qu as so so LDAA 35000 :Head data 0031 A7 00 sun x :sura n. at x 0033 an RT! 0034 02 00 mm m; eozoo :surung addrlss far :data sm—ega was oo oo 1‘sz FDB 30000 0033 CE 02 oo END? max #30200 :Rexmuauze man 0053 ll}? 34 six nun com 135 as LDX 11mm 0031' 39 R15 :Return {rum suhruutina :Tu user' 5 program

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

*Numbers in parentheses refer to MC6800 CPU pin out.

**Number or letters in brackets refer to standard M6800 system common bus code.

Figure 36. ADC0801-MC6800 CPU Interface

In order for the microprocessor to service subroutines and inter- rupts, the stack pointer must be dimensioned in the

user’s program.

Figure 37. Sample Program for Figure 36 ADC0801-MC6800 CPU Interface

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l IEXAS INSTRUMENTS ANALuu mrurs 0010 0015 0016 0019 001A 001D 0020 0021 0023 0025 0023 0023 002C 002E 0031 0053 0034 0036 0030 003A 0050 003E 0040 0042 0045 0047 150 DP 030030 F? F17 F8 E68006 4F 87 80 07 378006 OS 0334 563D F76007 375007 35 DE40 ECUZOF 270F 05 DFAO 2050 DE40 BS ED 06 A700 SB 0200 CE0200 DF40 39 DATAIN CONVRT INTRPI TEMP! END? ?IAORB PIACRE LDx sTx LDAA CLRA STAA STAA cnx LDAB LDAA STAB STAA WAI LDX crx BEQ xux srx BRA LDX LDAA STM RTI FDE LDX 51X RTS EQU zqu #30030 .FFFB PIAORB PIACRE PIAORE #854 #$3D PIACRB FIACRB mum £5020? END? TEMPI CONVRI TEMPI PIAORE x 60200 #00200 TEMFI $8005 $8007 ;Upaniﬁ§1awcyu :JumpstoOOSﬁ :Clear possibla W ﬂags :Sav. Pun, B as inpul §Starts ADCOBOI :Waitrorintsrrupn :15 final data Sta rad? :Read data in :szare iv. at X :starcingaddressrar :dataslarage :ReinlcializnTEMPl :Raturntromsubroutine :Tnusar'sprngram

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Figure 38. ADC0801–MC6820 PIA Interface

Figure 39. Sample Program for Figure 38 ADC0801–MC6820 PIA Interface

The following schematic and sample subroutine (DATA IN) in Auto-Zeroed Differential Transducer Amplifier and

ADC Converter section may be used to interface (up to) 8 ADC0801’s directly to the MC6800 CPU. This scheme

can easily be extended to allow the interface of more converters. In this configuration the converters are

(arbitrarily) located at HEX address 5000 in the MC6800 memory space. To save components, the clock signal is

derived from just one RC pair on the first converter. This output drives the other ADCs.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS m Mm" mu ms nu mum m [m [m D: an m m am my m an [m In nu mm m m m m m» m mum Azumﬂl "Inns AumHVI u: 45) um .. M4 v m mum- . on My . H w m ’ Wmlnl wxv‘ [7—° Luuw m m [H mm mm: m myml Anmnln 1/1 mm m mm: m mum

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

All the converters are started simultaneously with a STORE instruction at HEX address 5000. Note any other

HEX address of the form 5XXX will be decoded by the circuit, pulling all the CS inputs low. This can easily be

avoided by using a more definitive address decoding scheme. All the interrupts are ORed together to insure that

all ADCs have completed their conversion before the microprocessor is interrupted.

The subroutine, DATA IN, may be called from anywhere in the user’s program. Once called, this routine

initializes the CPU, starts all the converters simultaneously and waits for the interrupt signal. Upon receiving the

interrupt, it reads the converters (from HEX addresses 5000 through 5007) and stores the data successively at

(arbitrarily chosen) HEX addresses 0200 to 0207, before returning to the user’s pro- gram. All CPU registers then

recover the original data they had before servicing DATA IN.

9.2.3 Auto-Zeroed Differential Transducer Amplifier and ADC Converter

The differential inputs of the ADC0801 series eliminate the need to perform a differential to single ended

conversion for a differential transducer. Thus, one op amp can be eliminated because the differential to single

ended conversion is provided by the differential input of the ADC0801 series. In general, a transducer preamp is

required to take advantage of the full ADC converter input dynamic range.

*Numbers in parentheses refer to MC6800 CPU pin out.

**Numbers of letters in brackets refer to standard M6800 system common bus code.

Figure 40. Interfacing Multiple ADCs in an MC6800 System

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS ADDRESS 0010 0012 0015 0018 0013 0010 001D 0020 0022 0025 0027 0029 002A 002C 002E 00217 0031 ADDRESS 0033 0055 0038 003A 0055 0030 0051‘ 0040 0042 0044 HEX CODE DF 44 CE 00 2A F17 FY F8 B7 50 00 DE SE CE 50 00 DF 40 CE 02 00 DF 42 DE 44 59 DE 40 A6 00 08 DF 40 DE 42 HEX CODE A7 00 BC 02 07 27 05 08 D17 42 20 EB 33 50 00 02 00 00 00 DAIAIN INTFPT MNEMONICS S TX LDX S TX STAA CLI WAI LDX S TX LDX S TX LDX RTS LDX LDM I “X S TX LDX MNEMONICS RETURN I NDEXI INDEXZ TEN? STM m m mx STX BRA RT I FDB m FDB x #30207 RETURN INDEX? INTRPI 65000 60200 $0000 COMMENTS TEMP :SavaConLentsofX moon :UpunITQLow cvu sFFFs :Jumpstuoozn 85000 :StartsallA/D's :Waitforinlerrupl #35000 INDEX! :RasetbuthINDEX #30200 :1 and 2 to starting INDExz :addresses TEMP :Rsturnrromsubraucxne INDExl :1NDEX1 —» x K :Readdata in fromA/Datx :Incrament x by one INDEXI :X 4+ INDExl INDEXZ ; INDExz —v x COMMENTS :Store data ac X ;HavaallA/D'shsenraad? :Yes : branch to RETURN :No: lncramenl x by 0113 :x —+ INDEXZ :Eranch to 002A :SlartingaddrsssfurA/D :Starting addrosa for data storage

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Figure 41. Sample Program for Figure 40 Interfacing Multiple ADC’s in an MC6800 System

Figure 42. Sample Program for Figure 40 Interfacing Multiple ADC’s in an MC6800 System

Note: In order for the microprocessor to service subroutines and interrupts, the stack pointer must be

dimensioned in the user’s program.

For amplification of DC input signals, a major system error is the input offset voltage of the amplifiers used for

the preamp. Figure 43 is a gain of 100 differential preamp whose offset voltage errors will be cancelled by a

zeroing subroutine which is performed by the INS8080A microprocessor system. The total allowable input offset

voltage error for this preamp is only 50 µV for /⁄4 LSB error. This would obviously require very precise amplifiers.

The expression for the differential output voltage of the preamp is:

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS 5an Av mum-25w m kw. . 1 " t R mm nlmlm vu.‘ r: (mm m wanuvm mm mwum , 2R2 2R2 MWVNH][1+W]«(VOSZivoscvos::IXRX)[1+W] SIGNAL TAT DC ERROR TERM GA?

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

R2 = 49.5 R1

Switches are LMC13334 CMOS analog switches.

The 9 resistors used in the auto-zero section can be ±5% tolerance.

Figure 43. Gain of 100 Differential Transducer Preamp

where

• IXis the current through resistor RX(5)

All of the offset error terms can be cancelled by making ±IXRX= VOS1 + VOS3 −VOS2. This is the principle of this

auto-zeroing scheme.

The INS8080A uses the 3 I/O ports of an INS8255 Programable Peripheral Interface (PPI) to control the auto

zeroing and input data from the ADC0801 as shown in Figure 44. The PPI is programmed for basic I/O operation

(mode 0) with Port A being an input port and Ports B and C being output ports. Two bits of Port C are used to

alternately open or close the 2 switches at the input of the preamp. Switch SW1 is closed to force the preamp’s

differential input to be zero during the zeroing subroutine and then opened and SW2 is then closed for

conversion of the actual differential input signal. Using 2 switches in this manner eliminates concern for the ON

resistance of the switches as they must conduct only the input bias current of the input amplifiers.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS {"35 15 g a. rd INVIRYWG “5 B! I] ADHRKSS ﬂ “My“ InlﬂAAnDRESSEUS mm 7 ,1 r2 As H n r, :- um." 5V w i 1* E V v“ Tum PﬂRIA m T M Burns A'Daumnnnu . vw.,—<\’ner w="" i="" m="" m="" mm="" 7“="" mm="" 7,="" ma="" rm="" nd="" n,="" mm="" «any;="" amun="" mm="" mm="" -="" ;="" 7,7!“="" _l="" ,j,="" d"="" 7="" —r="" “.7="" puma="" “.7="" mum="" .="" mm="" mm="" -="" mm“;="" e-n="" mmnedii="" ‘—="">§n c; [.7 mm —>ﬁwsw‘ HOW : PHRYL IUFFERS Winn m WWW ——9ﬁvusw2 annuncumnm smms

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Output Port B is used as a successive approximation register by the 8080 and the binary scaled resistors in

series with each output bit create a D/A converter. During the zeroing subroutine, the voltage at Vxincreases or

decreases as required to make the differential output voltage equal to zero. This is accomplished by ensuring

that the voltage at the output of A1 is approximately 2.5V so that a logic "1" (5V) on any output of Port B will

source current into node VXthus raising the voltage at VXand making the output differential more negative.

Conversely, a logic "0" (0V) will pull current out of node VXand decrease the voltage, causing the differential

output to become more positive. For the resistor values shown, VXcan move ±12 mV with a resolution of 50 µV,

which will null the offset error term to /⁄4 LSB of full-scale for the ADC0801. It is important that the voltage levels

that drive the auto-zero resistors be constant. Also, for symmetry, a logic swing of 0V to 5V is convenient. To

achieve this, a CMOS buffer is used for the logic output signals of Port B and this CMOS package is powered

with a stable 5V source. Buffer amplifier A1 is necessary so that it can source or sink the D/A output current.

Figure 44. Microprocessor Interface Circuitry for Differential Preamp

A flow chart for the zeroing subroutine is shown in Figure 45. It must be noted that the ADC0801 series will

output an all zero code when it converts a negative input [VIN(−)≥VIN(+)]. Also, a logic inversion exists as all of

the I/O ports are buffered with inverting gates.

Basically, if the data read is zero, the differential output voltage is negative, so a bit in Port B is cleared to pull VX

more negative which will make the output more positive for the next conversion. If the data read is not zero, the

output voltage is positive so a bit in Port B is set to make VX more positive and the output more negative. This

continues for 8 approximations and the differential output eventually converges to within 5 mV of zero.

The actual program is given in Figure 46. All addresses used are compatible with the BLC 80/10 microcomputer

system. In particular:

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

• Port A and the ADC0801 are at port address E4

• Port B is at port address E5

• Port C is at port address E6

• PPI control word port is at port address E7

• Program Counter automatically goes to ADDR:3C3D upon acknowledgment of an interrupt from the ADC0801

9.2.4 Multiple ADC Converters in a Z-80 Interrupt Driven Mode

In data acquisition systems where more than one ADC converter (or other peripheral device) will be interrupting

pro- gram execution of a microprocessor, there is obviously a need for the CPU to determine which device

requires servicing. Figure 47 and the accompanying software is a method of determining which of 7 ADC0801

converters has completed a conversion (INTR asserted) and is requesting an interrupt. This circuit allows starting

the ADC converters in any sequence, but will input and store valid data from the converters with a priority

sequence of ADC 1 being read first, ADC 2 second, etc., through ADC 7 which would have the lowest priority for

data being read. Only the converters whose INT is asserted will be read.

The key to decoding circuitry is the DM74LS373, 8-bit D type flip-flop. When the Z-80 acknowledges the

interrupt, the program is vectored to a data input Z-80 subroutine. This subroutine will read a peripheral status

word from the DM74LS373 which contains the logic state of the INTR outputs of all the converters. Each

converter which initiates an interrupt will place a logic "0" in a unique bit position in the status word and the

subroutine will determine the identity of the converter and execute a data read. An identifier word (which

indicates which ADC the data came from) is stored in the next sequential memory location above the location of

the data so the program can keep track of the identity of the data entered.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS sum ZERDIME sunnnunui curs: 5w! arm 5w: l INHIALIZE sun In PDINTER am a : x 1n 1 mlmuz: sun DUDEIN an“; ass c=x'7r l uurvuTFIRsT SAR can FURY! x x n *— sum A/n AND nun mm: “on" an H mm REG :2 m mun an m mm a wum REAPPLIUJ smFr “1" m an: a nmurm Pom'rn) NE)" m l mm mm nus: swz IS an a 2mm 1 pump IS zsnnzn AND mom INPUT anvERsmus cm a: anE ‘rzxcwswpnwv use a mu nu; c Tl] SEY um [IT IN war a 1 nuvruv NEW sun can: w PERI a I_—____

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Figure 45. Flow Chart for Auto-Zero Routine

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS suuo 3590 um 90 51202 17521 on Control Pun :Frugram r91 snoa 2801 um H 01 Auto—Zero Subrouuna anus 7c Mov A.H SDD’I DSES BUT C :Closa SW1 npen SW2 EDD? 0580 MVIBSO :InSlialize Subit painter was 3371: MVI A 717 :Innianze 51m cade won 4F Mov C.A Raturn SDDE D3E5 DUTB :Fnrt E:SAR coda sum sum: m 52> sum sun :Dimenslon stack pumm- 51313 DSEd OUT A :Start A/D 5D15 FE IE 3mm 00 N0? Loop :Luop unulﬁassuua 3011 1:315:51) my Loop SDIA 7A Mov Ln Ame-Zero 51313 {1800 ADI 00 3111!) 01:21:31: stn c :TesLA/Duutpul data tax-zero 3920 73 uov LB smn a 31121 1300 an 00 :Clear carry SD23 117 MR :ShifL "1" 1115 right one place snza non an 00 :Is 3 zen? 1: ya: last 3qu cum: JZDana :appmxxmaucnhas beanmade 31729 47 MDV B.‘ 3132A C3333!) I“? New C 3m!) 79 no“, 5 Set c 3122}: E0 on E ;s.c b“. m c mm is in same 3122? 412 MochA :positxanas'l' in! 3930 C5203!) HIP Shift 3 5935 A9 XRA C New C :Clear bit in (I that 15 in 3534 CISDDJD JMF Racurn :same position as "1" in}! 3mm 47 nov a,A Done :lhen output new sAR cede. SDSE 7C HOV A.H :Open SW1 . class SW2 then was was xxx as ;pmesea W11h progrsm. Fraamp mm 0325 mm: :Xsnou zeroed. SDSD I Normal Prugram for prunessing proper aaxa values SCSI) DBE4 INA Read All) subroutine :RaadA/D data 30317 any xxx n mm“ data 3041 57 HOV D,‘ 3042 76 MOVA,E :IsBReg: PIfnat Stay 3C45 EBFF A“! PF :1n Hutu zero subrnuuna SEAS CZIASD INZ Auto—Zero SCAB 0331)“) 1K? Ila rum]

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

NOTE: All numerical values are hexadecimal representations.

Figure 46. Software for Auto-Zeroed Differential ADC

The following notes apply:

• It is assumed that the CPU automatically performs a RST 7 instruction when a valid interrupt is acknowledged

(CPU is in interrupt mode 1). Hence, the subroutine starting address of X0038.

• The address bus from the Z-80 and the data bus to the Z-80 are assumed to be inverted by bus drivers.

• ADC data and identifying words will be stored in sequential memory locations starting at the arbitrarily chosen

address X 3E00.

• The stack pointer must be dimensioned in the main program as the RST 7 instruction automatically pushes

the PC onto the stack and the subroutine uses an additional 6 stack addresses.

• The peripherals of concern are mapped into I/O space with the following port assignments:

Table 3. Port Assignment Where Peripherals are Mapped into I/O Space

HEX PORT ADDRESS PERIPHERAL HEX PORT ADDRESS PERIPHERAL

00 MM74C374 8-bit flip-flop 04 ADC 4

01 ADC 1 05 ADC 5

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS Muncsn m 01 n! m n; mi mu m nnuaus 1 :Muucau an “I nuv'" ms nu an an A/nx cum Mwamz mmm w a é an kn A/DB : WT: m cum $1 m '3 nu r» was : m m m m vs A vs i E n v. nmmm c v: m E nu k‘n AID! : w m mxm Ana: m V: \ 3 an n m a 5 nn a All) 1 ; m m cum nzl vn 3 m a m um I

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

Table 3. Port Assignment Where Peripherals are Mapped into I/O Space (continued)

HEX PORT ADDRESS PERIPHERAL HEX PORT ADDRESS PERIPHERAL

02 ADC 2 06 ADC 6

03 ADC 3 07 ADC 7

This port address also serves as the ADC identifying word in the program.

Figure 47. Multiple ADCs With Z-80 Type Microprocessor

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS INTERRUFT SERVICING SUBROUTINE LOC 0058 0039 003A 0033 0035 0040 0042 0044 0045 0046 0048 004K 0040 0040 0043 0051 0052 0055 0057 0059 005A 0053 0055 0050 0050 0061 0062 0065 OBJ CODE 55 05 F5 21 00 3E 0E01 0300 DBOO 47 79 FE OS CAsoon 78 IF 47 DA 5500 00 C5 4500 ED 78 BE FF 77 20 71 2C 035100 P1 01 £1 09 TEST NEXT LOAD DONE SOURCE STATEMENT FUSH HL PUSH ac PUSH AF Ln (Hm ,xsaoo LD c. x01 our 100, A INA, xoo LD EM Ln A. c or, 105 JFZ. nous m: A.ia RRA LD 3.». JPC, LOAD INC 0 JPJEST mA, (0) x0): FF u) (HL) ,A ma L LD (HL) ,0 ma L JPJEXT POP AF POP 5c POP HL Rn COMMENT :save contents at 311 registers affected by : this subroutine. - Assumed INT mode 1 esrusr set . nitieuze memory pointer where data will bu stared. , registerwin be part ADDR ofA/D convarters. :Lead paripheral status ward inte 5-bit latch. cad status ward into accumulator. ave the status ward. , est to see “the status at an A/D's have :beenchecked.Itse.exitsuhrout1ne :Tesl. a single bit in status word by unkiing {or '1" Lobe rotated inte the um (an m s loaded as a "1“) . If CARRY is set tnen load ontents an)» at part ADDR in c register. r CARRY is net set , increment a register to point ; to next A/D, then test next bit 311 status word. :Raad data from interrupting A/D and invert : the data. :SLDI‘B the data ;5tere A/D identifier (AID part ADDR) . :TesL next hit in status word. :Ra-establisn an registers as they were :bs rare the Antermpti :Return to original pregren

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS E: a: vm W m: um: am 5501 R1, m m m: w < mu="" vie="" (wu)="" 0="" m="" —i="" v="" i="" mm="" ”b="" :="" i="" i="" i="" "n="" _l.="" viii="" i="" i="" i="" i="" n="" i="" i="" i="" l—vmm="" vngll="" :="" 2="" :="" l____j="" _="" imam="" anmust="" o—="" vva="" vcc‘="" all:="" 0—="" va="" van/2‘="" vcc="" '="" vaer="" (5va="" o—="" vmw="" am="" 0—="" vinh="" ﬂptiﬂnal="" f3="" aanst="">

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

9.3 System Examples

*For low power, see also LM385–2.5

Figure 48. 6800 Interface Figure 49. Absolute With a 2.5-V Reference

Note: before using caps at VIN or VREF/2, see section Input Bypass

Capacitors.

Figure 50. Ratiometeric With Full-Scale Adjust Figure 51. Absolute With a 5-V Reference

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

TEXAS INSTRUMENTS vmm "a? .m Jr W , mum cunivmuci m w n nut 11. mm m Vcc In,r 2h 15v m Vcc (5VDcl Vcc + TM All] Vner/Z -‘_-

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

System Examples (continued)

Figure 52. Zero-Shift and Span Adjust: 2 V ≤VIN ≤5 Figure 53. Span Adjust: 0 V ≤VIN ≤3 V

VREF/2 = 256 mV

For: VIN(+)>VIN(−); Output = FFHEX

For: VIN(+) < VIN(−); Output = 00HEX

Figure 54. Directly Converting a Low-Level Signal Figure 55. A µP Interfaced Comparator

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS vwé .4. "5‘ u” O— M“) ELK n 0— VmH Ink mm mm mm cLKm E MD ISDaF RT W ‘mm mm 0 rm 1qu n ma s'mm' mm = cum I I § IF mm: mm s Anlmvrmu um, us: A was mm: mm ﬂu

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

System Examples (continued)

VREF/2=128 mV; 1 LSB =1 mV; VDAC ≤VIN ≤(VDAC + 256 mV); 0 ≤

VDAC < 2.5 V

Figure 56. 1-mV Resolution With µP-Controlled Figure 57. Digitizing a Current Flow

Range

*After power up, a momentary grounding of the WR input is needed

to ensure operation.

* Use a large R value to reduce loading at CLK R output.

Figure 58. Self-Clocking Multiple ADCs Figure 59. Self-Clocking in Free-Running Mode

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS as: wan”; VcLK Iksil mm mm m W Drums: mm M,» mm"; nu mm In: pm Man: m _____ 1.7V MINI W" Lav MAX n um 'CLK >— ch m V2: 15 m1 VB: My 0 m VXM VmM Van u . IERn VmV'V m w n .mm m Wu W my” ;; + All. W T u. w: mu

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

System Examples (continued)

100 kHz ≤fCLK ≤1460 kHz

Figure 60. µP Interface for Free-Running ADC Figure 61. External clocking

*VIN(−) = 0.15 VCC

15% of VCC ≤VXDR ≤85% of VCC

Figure 62. Operating With “Automotive” Figure 63. Ratiometric With VREF/2 Forced

Ratiometric Transducers

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS w. v. m mm mm :IIIV m'

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

System Examples (continued)

*Select R value DB7 = “1” for VIN(+)>VIN(−)+(VREF/2). Omit circuitry

within the dotted area if hysteresis is not needed.

*Beckman Instruments #694-3-R10K resistor array

Figure 64. µP-Compatible Differential-Input Figure 65. Handling ±10-V Analog Inputs

Comparator With Pre-Set VOS (With or Without

Hysteresis)

**Can calibrate each sensor to allow easy replacement, then ADC

can be calibrated with a pre-set input voltage.

Figure 66. Low-Cost, µP-Interfaced, Temperature- Figure 67. µP-Interfaced Temperature-to-Digital

to-Digital Converter Converter

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS V“ pp nus ‘5 "am (3 7 —’° ‘5 DATA E W AID w“ —> mm P va ﬁ DATA Is sums new auTPuT couvmsmu vmh) MSB (nan Vm DIE —’ I) UTPUT A/D A/D J.— Vm (-)

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

System Examples (continued)

*Beckman Instruments #694-3-R10K resistor array

Figure 68. Handling ±5-V Analog Inputs Figure 69. Read-Only Interface

Diodes are 1N914

Figure 70. µP-Interfaced Comparator With Figure 71. Protecting the Input

Hysteresis

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS o— VwM O— 'm W» 0— mm . 5mm 0—- mm“ mm Mun: MD M vumvs o— umx . mm C ﬁrm", m 7 m "' ""W ' mm mm 0— VmH _ o— . m m. 1* 1- 1c mum mm W m rauMnuquv 3312')? , _ 2.. b mmm ‘ , -I F”; "H . A, 9,0, D= LMSZAA H; mm (— mm W m Hammm “W mm mm mm mm m m '- w w VnEm m» m m ‘ mm _ nu L— J_— m 9| "MI 1.. m ‘V' 5w ‘_ m ‘ .3 2"; n “I

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

System Examples (continued)

*LM389 transistors A, B, C, D = LM324A quad op amp

Figure 72. Analog Self-Test for a System Figure 73. A Low-Cost, 3-Decade Logarithmic

Converter

fC=20 Hz

Uses Chebyshev implementation for steeper roll-off unity-gain, 2nd

order, low-pass filter

Adding a separate filter for each channel increases system response

time if an analog multiplexer is used

Figure 74. 3-Decade Logarithmic ADC Converter Figure 75. Noise Filtering the Analog Input

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS , foﬁ o— 7 cm _ vmw ”W mm + EZZZDo—w > ‘33:" > o— r»: 7 , 0— CHANNEL 7 , DIFFERENTIAL A/D roan o— MUX “3‘, annual o— + 7 0—: cm _ mm o— 1“ lummuu SElEL‘I ~._,___, FREMOUYFHT MINOR»! ESP—0f: W _. 5m! "‘1' w 'iVVV um i mum" nArnaus Si w W m_. r»— W w j 'it‘r's‘éli" :> g L. i—W _ w. n r! gem? 5m m W. m | y .r n j a W m :

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

System Examples (continued)

*ADC output data is updated 1 CLK period prior to assertion of INTR

Figure 76. Output Buffers With ADC Data Enabled Figure 77. Multiplexing Differential Inputs

(2) Consider the amplitude errors which are introduced within the

passband of the filter.

*Allows output data to set-up at falling edge of CS

Figure 78. Increasing Bus Drive and/or Figure 79. Sampling an AC Input Signal

Reducing Time on Bus

(Complete shutdown takes ≈30 seconds.)

Buffer prevents data bus from overdriving output of ADC when in

shutdown mode.

Figure 80. 70% Power Savings by Clock Gating Figure 81. Power Savings by ADC and VREF

Shutdown

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

www.ti.com

10 Power Supply Recommendations

Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in

polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge

through the resulting forward diode within the device could cause fusing of the internal conductors and result in a

destroyed unit.

Noise spikes on the VCC supply line can cause conversion errors as the comparator will respond to this noise. A

low-inductance, low-ESR tantalum bypass capacitor should be used close to the converter VCC pin, and a 10-µF

is recommended. If an unregulated voltage is available in the system, a separate 5-V voltage regulator for the

converter (and other analog circuitry) will greatly reduce digital noise on the VCC supply.

11 Layout

11.1 Layout Guidelines

All logic signal wires and leads should be grouped and kept as far away as possible from the analog signal

leads. Exposed leads to the analog inputs can cause undesired digital noise and 60-Hz pickup. Shielded leads

for the analog inputs may be required in sensitive applications. A single-point analog ground should be used that

is also separated from the logic ground points. The power supply bypass capacitor should be returned to digital

ground. Any VREF/2 bypass capacitors, analog input filter capacitors, or input signal shielding should be returned

to the analog ground point. A test for proper grounding is to measure the zero error of the ADC converter. Zero

errors in excess of 1/4 LSB is generally traceable to improper PCB layout and/or wiring.

To minimize potential offset issues, TI recommends to route the signal traces differentially next to each other so

that they will see the same thermal gradients and the same number of feedthroughs. Furthermore, inductance is

determined by the size of the loop of current. Providing a path for return currents next to the signal trace will

reduce the inductance. A solid ground plane is very advantageous in this regard. Ensure to minimize the loop

area formed by the bypass capacitor connection between VCC and ground. The ground pin should be connected

to the PCB ground plane at the pin of the device.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

l TEXAS INSTRUMENTS

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

www.ti.com

SNOSBI1C –NOVEMBER 2009–REVISED JUNE 2015

12 Device and Documentation Support

12.1 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to sample or buy.

Table 4. Related Links

TECHNICAL TOOLS & SUPPORT &

PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY

ADC0801 Click here Click here Click here Click here Click here

ADC0802 Click here Click here Click here Click here Click here

ADC0803 Click here Click here Click here Click here Click here

ADC0804 Click here Click here Click here Click here Click here

ADC0805 Click here Click here Click here Click here Click here

12.2 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective

contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of

Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration

among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help

solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and

contact information for technical support.

12.3 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

12.4 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

12.5 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

Product Folder Links: ADC0801 ADC0802 ADC0803 ADC0804 ADC0805

I TEXAS INSTRUMENTS Samples Samples Samples

PACKAGE OPTION ADDENDUM

www.ti.com 10-Dec-2020

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead finish/

Ball material

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

ADC0802LCWM/NOPB ACTIVE SOIC DW 20 36 RoHS & Green SN Level-3-260C-168 HR 0 to 70 ADC0802

LCWM

ADC0804LCWM/NOPB ACTIVE SOIC DW 20 36 RoHS & Green SN Level-3-260C-168 HR 0 to 70 ADC0804

LCWM

ADC0804LCWMX/NOPB ACTIVE SOIC DW 20 1000 RoHS & Green SN Level-3-260C-168 HR 0 to 70 ADC0804

LCWM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two

lines if the finish value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

I TEXAS INSTRUMENTS

PACKAGE OPTION ADDENDUM

www.ti.com 10-Dec-2020

Addendum-Page 2

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

I TEXAS INSTRUMENTS ‘3‘ V.'

PACKAGE MATERIALS INFORMATION

www.ti.com 9-Aug-2022

TAPE AND REEL INFORMATION

Reel Width (W1)

REEL DIMENSIONS

Dimension designed to accommodate the component length

Dimension designed to accommodate the component thickness

Overall width of the carrier tape

Pitch between successive cavity centers

Dimension designed to accommodate the component width

TAPE DIMENSIONS

K0 P1

B0 W

Cavity

QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE

Pocket Quadrants

Sprocket Holes

Q1 Q1Q2 Q2

Q3 Q3Q4 Q4 User Direction of Feed

Reel

Diameter

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

ADC0804LCWMX/NOPB SOIC DW 20 1000 330.0 24.4 10.9 13.3 3.25 12.0 24.0 Q1

Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION

www.ti.com 9-Aug-2022

TAPE AND REEL BOX DIMENSIONS

Width (mm)

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

ADC0804LCWMX/NOPB SOIC DW 20 1000 367.0 367.0 45.0

Pack Materials-Page 2

I TEXAS INSTRUMENTS __________________ ‘(I(I“""""""""

PACKAGE MATERIALS INFORMATION

www.ti.com 9-Aug-2022

TUBE

L - Tube length

T - Tube

height

W - Tube

width

B - Alignment groove width

*All dimensions are nominal

Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm)

ADC0802LCWM/NOPB DW SOIC 20 36 495 15 5842 7.87

ADC0804LCWM/NOPB DW SOIC 20 36 495 15 5842 7.87

Pack Materials-Page 3

DW0020A I

www.ti.com

PACKAGE OUTLINE

TYP

10.63

9.97

2.65 MAX

18X 1.27

20X 0.51

0.31

11.43

TYP

0.33

0.10

0 - 8

0.3

0.1

0.25

GAGE PLANE

1.27

0.40

NOTE 3

13.0

12.6

B7.6

7.4

4220724/A 05/2016

SOIC - 2.65 mm max heightDW0020A

SOIC

NOTES:

1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed 0.15 mm per side.

4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.43 mm per side.

5. Reference JEDEC registration MS-013.

120

0.25 C A B

PIN 1 ID

AREA

NOTE 4

SEATING PLANE

0.1 C

SEE DETAIL A

DETAIL A

TYPICAL

SCALE 1.200

DW0020A

www.ti.com

EXAMPLE BOARD LAYOUT

(9.3)

0.07 MAX

ALL AROUND

0.07 MIN

ALL AROUND

20X (2)

20X (0.6)

18X (1.27)

(R )

TYP

0.05

4220724/A 05/2016

SOIC - 2.65 mm max heightDW0020A

SOIC

SYMM

LAND PATTERN EXAMPLE

SCALE:6X

10 11

NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

METAL

SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

SOLDER MASK DETAILS

SOLDER MASK

OPENING

METAL UNDER

SOLDER MASK

DEFINED

DW0020A $$$$$ﬁﬁﬁiﬁ%

www.ti.com

EXAMPLE STENCIL DESIGN

(9.3)

18X (1.27)

20X (0.6)

20X (2)

4220724/A 05/2016

SOIC - 2.65 mm max heightDW0020A

SOIC

NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

9. Board assembly site may have different recommendations for stencil design.

SYMM

10 11

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

SCALE:6X

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, regulatory or other requirements.

These resources are subject to change without notice. TI grants you permission to use these resources only for development of an

application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license

is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you

will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these

resources.

TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with

such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for

TI products.

TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

ADC0801-05 Datasheet by Texas Instruments

INFORMATION

HELP

CONTACT US

FOLLOW US