Scheda tecnica SN54F245, SN74F245 di Texas Instruments

[ U [ E . . A3 4 l7 description A4 [ 5 ‘6 These octal bus transceivers are designed lor A5 [ 5 15 asynchronous communication between data As [ 7 14 buses. The devices transmit data lrom the A bus A7 [ a 13 to the B bus or from the B bus to the A bus AB [ 9 12 depending upon the logic level at the GND [ m 11 diriectionrcontroi (DIR) input. The output enable (OE) inputcan be used to disable the device sothe buses are effectively isolated. The SN74F245 is available in Tl's shrink smailroutline package (DB), which provides the i same I/O pin count and functionality of standard smailroutline packages in less than half the printedrcircuitrboard area. The SN54F245 is characterized lor operation over the lull military temperature range of 755°C to 125°C. The SN74F245 is characterized for operation lrom 0°C to 70"C. FUNCTION TABLE INPUTS _ OPERATION OE DIR L L B data to A bus L H A data to B bus H X isolatlon r—u—u—u—u—r Copyright 1993 ‘9 TEXAS INSTRUMENTS POST orncz BOX 655303 - DALLAS TEXAS 752s5
SN54F245, SN74F245
OCTAL BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SDFS010A – MARCH 1987 – REVISED OCTOBER 1993
Copyright 1993, Texas Instruments Incorporated
2–1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
3-State Outputs Drive Bus Lines Directly
Package Options Include Plastic
Small-Outline (SOIC) and Shrink
Small-Outline (SSOP) Packages, Ceramic
Chip Carriers, and Plastic and Ceramic
DIPs
description
These octal bus transceivers are designed for
asynchronous communication between data
buses. The devices transmit data from the A bus
to the B bus or from the B bus to the A bus
depending upon the logic level at the
direction-control (DIR) input. The output enable
(OE) input can be used to disable the device so the
buses are effectively isolated.
The SN74F245 is available in TI’s shrink
small-outline package (DB), which provides the
same I/O pin count and functionality of standard
small-outline packages in less than half the
printed-circuit-board area.
The SN54F245 is characterized for operation over
the full military temperature range of –55°C to
125°C. The SN74F245 is characterized for
operation from 0°C to 70°C.
FUNCTION TABLE
INPUTS
OPERATION
OE DIR
OPERATION
L L B data to A bus
L H A data to B bus
H X Isolation
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
DIR
A1
A2
A3
A4
A5
A6
A7
A8
GND
VCC
OE
B1
B2
B3
B4
B5
B6
B7
B8
SN54F245 ...J PACKAGE
SN74F245 . . . DB, DW, OR N PACKAGE
(TOP VIEW)
3212019
910 11 12 13
4
5
6
7
8
18
17
16
15
14
B1
B2
B3
B4
B5
A3
A4
A5
A6
A7
A2
A1
DIR
B7
B6 OE
A8
GND
B8 VCC
SN54F245 . . . FK PACKAGE
(TOP VIEW)
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
OE DIR Al A2 A3 A4 A5 A6 A7 A8 63 3EN1[BA] asuzua] V Bl 52 53 54 BS BS B7 BB *9 TEXAS INSTRUMENTS p057 omcg aox $553133 - DALLAS IEXAS 752s5
SN54F245, SN74F245
OCTAL BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SDFS010A – MARCH 1987 – REVISED OCTOBER 1993
2–2 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
logic symbollogic diagram (positive logic)
A5 6
A6 7
A7 8
A8 9
A2 3
A3 4
A4 5
OE
A1 2
G3
19
3EN2[AB]
B5
14
B6
13
B7
12
B8
11
B1
18
B2
17
B3
16
B4
15
3EN1[BA]
1
DIR
DIR
OE
A1
B1
1
2
18
19
To Seven Other Channels
1
2
This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC 0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (except I/O ports) (see Note 1) 1.2 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current range 30 mA to 5 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage range applied to any output in the disabled or power-off state 0.5 V to 5.5 V. . . . . . . . . . . . . . . . . . .
Voltage range applied to any output in the high state 0.5 V to VCC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current into any output in the low state: SN54F245 (A1 thru A8) 40 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN54F245 (B1 thru B8) 96 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN74F245 (A1 thru A8) 48 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN74F245 (B1 thru B8) 128 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range: SN54F245 55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN74F245 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range 65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The input voltage ratings may be exceeded provided the input current ratings are observed.
vahrleHet amp-101mm Lam have) cv‘tp“! c-‘rvent PARAMETER TEST CONDITIONS VM H {5‘ TEXAS INSTRUM NTS
SN54F245, SN74F245
OCTAL BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SDFS010A – MARCH 1987 – REVISED OCTOBER 1993
2–3
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
recommended operating conditions
SN54F245 SN74F245
UNIT
MIN NOM MAX MIN NOM MAX
UNIT
VCC Supply voltage 4.5 5 5.5 4.5 5 5.5 V
VIH High-level input voltage 2 2 V
VIL Low-level input voltage 0.8 0.8 V
IIK Input clamp current –18 –18 mA
IOH
High level out
p
ut current
A1 thru A8 –3 –3
mA
I
OH
High
-
le
v
el
o
u
tp
u
t
c
u
rrent
B1 thru B8 –12 –15
mA
I
OL
Low level out
p
ut current
A1 thru A8 20 24
mA
I
OL
Lo
w-
le
v
el
o
u
tp
u
t
c
u
rrent
B1 thru B8 48 64
mA
TAOperating free-air temperature –55 125 0 70 °C
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
SN54F245 SN74F245
UNIT
PARAMETER
TEST
CONDITIONS
MIN TYPMAX MIN TYPMAX
UNIT
VIK VCC = 4.5 V, II = –18 mA 1.2 1.2 V
VCC =45V
IOH = – 1 mA 2.5 3.4 2.5 3.4
u
V
CC =
4
.
5
V
IOH = – 3 mA 2.4 3.3 2.4 3.3
VOH
VCC =45V
IOH = – 12 mA 2 3.2 V
u
V
CC =
4
.
5
V
IOH = – 15 mA 2 3.1
Any output VCC = 4.75 V, IOH = –1 mA to – 3 mA 2.7
VCC =45V
IOL = 20 mA 0.3 0.5
VOL
u
V
CC =
4
.
5
V
IOL = 24 mA 0.35 0.5
V
V
OL
VCC =45V
IOL = 48 mA 0.38 0.55
V
u
V
CC =
4
.
5
V
IOL = 64 mA 0.42 0.55
II
A and B
VCC =55V
VI = 5.5 V 1 1
mA
I
IDIR, OE
V
CC =
5
.
5
V
VI = 7 V 0.1 0.1
mA
I
A and B
VCC =55V
VI=27V
70 70
µA
I
IH
DIR, OE
V
CC =
5
.
5
V
,
V
I =
2
.
7
V
20 20 µ
A
I
A and B
VCC =55V
VI=05V
0.65 –0.65
mA
I
IL
DIR, OE
V
CC =
5
.
5
V
,
V
I =
0
.
5
V
– 1.2 – 1.2
mA
IOS§
A1 thru A8
VCC =55V
VO=0
–60 150 –60 150
mA
I
OS
§
B1 thru B8
V
CC =
5
.
5
V
,
V
O =
0
100 –225 100 –225
mA
Outputs high 70 90 70 90
ICC VCC = 5.5 V Outputs low 95 120 95 120 mA
Outputs disabled 85 110 85 110
All typical values are at VCC = 5 V, TA = 25°C.
For I/O ports, the parameters IIH and IIL include the off-state output current.
§Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
(INPUT) (OUTPUT) *9 TEXAS INSTRUMENTS
SN54F245, SN74F245
OCTAL BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SDFS010A – MARCH 1987 – REVISED OCTOBER 1993
2–4 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
switching characteristics (see Note 2)
PARAMETER FROM
(
INPUT
)
TO
(
OUTPUT
)
VCC = 5 V,
CL = 50 pF,
RL = 500 ,
TA = 25°C
VCC = 4.5 V to 5.5 V,
CL = 50 pF,
RL = 500,
TA = MIN to MAXUNIT
(INPUT)
(OUTPUT)
F245 SN54F245 SN74F245
MIN TYP MAX MIN MAX MIN MAX
tPLH
AorB
BorA
1.7 3.8 6 1.2 7.5 1.7 7
ns
tPHL
A
or
B
B
or
A
1.7 4.2 6 1.2 7.5 1.7 7
ns
tPZH
OE
AorB
2.2 4.9 7 1.7 9 2.2 8
ns
tPZL
OE
A
or
B
2.7 5.6 8 2.2 10 2.7 9
ns
tPHZ
OE
AorB
2.2 4.6 6.5 1.7 9 2.2 7.5
ns
tPLZ
OE
A
or
B
1.2 4.6 6.5 1.2 10 1.2 7.5
ns
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
NOTE 2: Load circuits and waveforms are shown in Section 1.
{I} TEXAS INSTRUMENTS
PACKAGE OPTION ADDENDUM
www.ti.com 10-Jun-2022
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
85511012A ACTIVE LCCC FK 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 85511012A
SNJ54F
245FK
Samples
8551101RA ACTIVE CDIP J 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 8551101RA
SNJ54F245J Samples
8551101SA ACTIVE CFP W 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 8551101SA
SNJ54F245W Samples
JM38510/34803B2A ACTIVE LCCC FK 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 JM38510/
34803B2A Samples
JM38510/34803BRA ACTIVE CDIP J 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 JM38510/
34803BRA Samples
JM38510/34803BSA ACTIVE CFP W 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 JM38510/
34803BSA Samples
M38510/34803B2A ACTIVE LCCC FK 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 JM38510/
34803B2A Samples
M38510/34803BRA ACTIVE CDIP J 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 JM38510/
34803BRA Samples
M38510/34803BSA ACTIVE CFP W 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 JM38510/
34803BSA Samples
SN54F245J ACTIVE CDIP J 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 SN54F245J Samples
SN74F245DBR ACTIVE SSOP DB 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 F245 Samples
SN74F245DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 F245 Samples
SN74F245DWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 F245 Samples
SN74F245N ACTIVE PDIP N 20 20 RoHS &
Non-Green NIPDAU N / A for Pkg Type 0 to 70 SN74F245N Samples
SN74F245NE4 ACTIVE PDIP N 20 20 RoHS &
Non-Green NIPDAU N / A for Pkg Type 0 to 70 SN74F245N Samples
SN74F245NSR ACTIVE SO NS 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 74F245 Samples
SNJ54F245FK ACTIVE LCCC FK 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 85511012A
SNJ54F Samples
Addendum-Page 1
I TEXAS INSTRUMENTS
PACKAGE OPTION ADDENDUM
www.ti.com 10-Jun-2022
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
245FK
SNJ54F245J ACTIVE CDIP J 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 8551101RA
SNJ54F245J Samples
SNJ54F245W ACTIVE CFP W 20 1 Non-RoHS
& Green SNPB N / A for Pkg Type -55 to 125 8551101SA
SNJ54F245W Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
TEXAS INSTRUMENTS
PACKAGE OPTION ADDENDUM
www.ti.com 10-Jun-2022
OTHER QUALIFIED VERSIONS OF SN54F245, SN74F245 :
Catalog : SN74F245
Military : SN54F245
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
Military - QML certified for Military and Defense Applications
Addendum-Page 3
I TEXAS INSTRUMENTS ‘3‘ V.'
PACKAGE MATERIALS INFORMATION
www.ti.com 3-Jun-2022
TAPE AND REEL INFORMATION
Reel Width (W1)
REEL DIMENSIONS
A0
B0
K0
W
Dimension designed to accommodate the component length
Dimension designed to accommodate the component thickness
Overall width of the carrier tape
Pitch between successive cavity centers
Dimension designed to accommodate the component width
TAPE DIMENSIONS
K0 P1
B0 W
A0
Cavity
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Pocket Quadrants
Sprocket Holes
Q1 Q1Q2 Q2
Q3 Q3Q4 Q4 User Direction of Feed
P1
Reel
Diameter
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
SN74F245DBR SSOP DB 20 2000 330.0 16.4 8.2 7.5 2.5 12.0 16.0 Q1
SN74F245DWR SOIC DW 20 2000 330.0 24.4 10.8 13.3 2.7 12.0 24.0 Q1
SN74F245NSR SO NS 20 2000 330.0 24.4 8.4 13.0 2.5 12.0 24.0 Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 3-Jun-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
W
L
H
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN74F245DBR SSOP DB 20 2000 356.0 356.0 35.0
SN74F245DWR SOIC DW 20 2000 367.0 367.0 45.0
SN74F245NSR SO NS 20 2000 367.0 367.0 45.0
Pack Materials-Page 2
I TEXAS INSTRUMENTS
PACKAGE MATERIALS INFORMATION
www.ti.com 3-Jun-2022
TUBE
L - Tube length
T - Tube
height
W - Tube
width
B - Alignment groove width
*All dimensions are nominal
Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm)
85511012A FK LCCC 20 1 506.98 12.06 2030 NA
JM38510/34803B2A FK LCCC 20 1 506.98 12.06 2030 NA
M38510/34803B2A FK LCCC 20 1 506.98 12.06 2030 NA
SN74F245DW DW SOIC 20 25 507 12.83 5080 6.6
SN74F245N N PDIP 20 20 506 13.97 11230 4.32
SN74F245NE4 N PDIP 20 20 506 13.97 11230 4.32
SNJ54F245FK FK LCCC 20 1 506.98 12.06 2030 NA
Pack Materials-Page 3
MECHANICAL DATA AME; CHEF“ ELAR‘REE ?< (a="" cm;="" w”)="" ,eamess="" c="" ’7="" flflflflflfl\="" f="" e="" e="" e="" e="" ,="" kwwwg="" qfijrm“="" a="" i:="" i7="" i4="" i:="" i:="" e7="" eiflfiiflfizj="" vvwwttflfl="" 1="" notes="" ah="" ineur="" dimensions="" are="" in="" inches="" (minmeiers).="" this="" cruwg="" i5="" subjeci="" i0="" chcnge="" without="" noiice="" this="" package="" car="" he="" hermeticuiiy="" secied="" mm="" a="" metai="" ic="" i'ciis="" wiihi="" jedec="" n87004="" 50m)="" {mm="" instruments="" w.="" (i.="" cam="">
I-III
www.ti.com
PACKAGE OUTLINE
C
18X 0.65
2X
5.85
20X 0.38
0.22
8.2
7.4 TYP
SEATING
PLANE
0.05 MIN
0.25
GAGE PLANE
0 -8
2 MAX
B5.6
5.0
NOTE 4
A
7.5
6.9
NOTE 3
0.95
0.55
(0.15) TYP
SSOP - 2 mm max heightDB0020A
SMALL OUTLINE PACKAGE
4214851/B 08/2019
1
10
11
20
0.1 C A B
PIN 1 INDEX AREA
SEE DETAIL A
0.1 C
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-150.
A 15
DETAIL A
TYPICAL
SCALE 2.000
“‘w“‘+“‘w“‘
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAX
ALL AROUND 0.07 MIN
ALL AROUND
20X (1.85)
20X (0.45)
18X (0.65)
(7)
(R0.05) TYP
SSOP - 2 mm max heightDB0020A
SMALL OUTLINE PACKAGE
4214851/B 08/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 10X
SYMM
SYMM
1
10 11
20
15.000
METAL
SOLDER MASK
OPENING METAL UNDER
SOLDER MASK SOLDER MASK
OPENING
EXPOSED METAL
EXPOSED METAL
SOLDER MASK DETAILS
NON-SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK
DEFINED
mi: 2.5%
www.ti.com
EXAMPLE STENCIL DESIGN
20X (1.85)
20X (0.45)
18X (0.65)
(7)
(R0.05) TYP
SSOP - 2 mm max heightDB0020A
SMALL OUTLINE PACKAGE
4214851/B 08/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE: 10X
SYMM
SYMM
1
10 11
20
MECHANICAL DATA NS (R-PDSO-G") PLASTIC SMALL—OUTLINE PACKAGE 14-PINS SHOWN HHFHHFH j j t t H H j, A jfi/—\ % lgLLLLLiLLL/fiif A MAX 1060 1060 1290 1530 A MW 990 9,90 1230 14‘70 4040062/0 03/03 VOTES: A. AH Hneur dimenswons are m mHHmetevs a, Tm: druwmg 5 subject to change wmom name. 0 Body dwmenswons do not mamas mom flash 0v pmtmswom not to exceed 0,15 INSTRUMEN'IS www.li.m
J (R76D1P7TM) CERAVVHC DUAL 1N7L1NE PACKAGE )4 LEADS SHOWN PWS u . W 14 e 18 20 0300 0300 0300 0300 E (7.52) (7.52) (7.62) (7.62) w 5 Est ass ass ass fl fl m m m m m E MAX 0.755 540 0.950 1.060 (19.94) (21.34) (24.35) (25.92) I ..15,,, 1 0 500 0,300 0,310 0.300 U U U U U U U C W (7.52) (7.52) (7.57) (7.52) 0.245 0.245 0.220 0.245 0.005 (1.65) 0 MW 0045 (1.14) (6.22) (6.22) (5.50) (6.22) 0000 ( . ) a «0005(0.13)MN m r ~ 0200 (5.05) MAX 7 ; Seatmg Pmne , 0 (3.30) MN 4 0 020 (0. 66) 0014 (0.36) 0715' 0100 (.)254 0.014 (0.36) 0,000 (0.20) 4040083/F 03/03 VOTES: A. AH Hneur d1mens1ons are 1’1 1mm (muhmeters) a, This druwmg '3 subject m change w'thout nnt'ce. 0, 1m package 15 hermehcoHy sewed mm a cemm 11a usmg q1ass mt. D. 11an pom 1’s prowded on cap fo' 1mm) 1den1111ca0an umy on press cemrmc 9055 m sea) 00W. E FaHs thin ML 513 1035 0011417114. 001141416. GDPPTTB 0'10 001017120
MECHANICAL DATA N (R—PDlP-T“) PLASTIC DUAL—IN—LINE PACKAGE 16 P15 SHOWN PWS " A L . [NM 15 a 20 16 9 0 775 U 777 0 SZU '1 USE 3 , 1H HH HH r% r’H r"—1 r’H H1 1 A VAX “9‘69? (191591 (23,37) (25,92) 0 250 (6,50‘ A MN [1145‘ 0142‘ 0.350 new 3 O 240 (6.10), 15 92/ (1832/ (2 .59) (23,58) MSiUO‘ (A AA AA Ari AA AA AA R1 &. VAR1AT1CN M RR AC AD 1 B 0070( (17s) 0015 (111) A 0045 (1,111 g n > , ‘ -) 3.020 (0,51) MW w o 5 (0 35) 0200( 38) MAX f, ), Gnu E Home 1 1‘ 9 fix—1%)” 1 0125’ 1/111 4% 0010 (v.37 ) NOM 31a) U L»- J 0450 (13,92) MAX L 202‘ (0,53) » e c 015 (0,35) / \ a; 00‘s (0,Zb)® / \ 1 1 \\¥,// 11/18 Pm (My > @ 20 Pm vendor upho'v mom/r 17/7037 NO'FS A AH Mnec' mmensmr‘fi: B 1m: drawmq 1s sume m muss (m1111mevem) 0 change mm): nofice /c\ FuHs wumn JEDEC M57001, except 15 an: 20 p171 'r1111mLm body 1mm (01m A) A The 70 p171 and 15m} shmflder Md” 15 a ve'vdnr 0311071, eher NIH Dr 111 wkflh INSI'RUMENTS www.1i.com
DW0020A I
www.ti.com
PACKAGE OUTLINE
C
TYP
10.63
9.97
2.65 MAX
18X 1.27
20X 0.51
0.31
2X
11.43
TYP
0.33
0.10
0 - 8
0.3
0.1
0.25
GAGE PLANE
1.27
0.40
A
NOTE 3
13.0
12.6
B7.6
7.4
4220724/A 05/2016
SOIC - 2.65 mm max heightDW0020A
SOIC
NOTES:
1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.43 mm per side.
5. Reference JEDEC registration MS-013.
120
0.25 C A B
11
10
PIN 1 ID
AREA
NOTE 4
SEATING PLANE
0.1 C
SEE DETAIL A
DETAIL A
TYPICAL
SCALE 1.200
DW0020A
www.ti.com
EXAMPLE BOARD LAYOUT
(9.3)
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
20X (2)
20X (0.6)
18X (1.27)
(R )
TYP
0.05
4220724/A 05/2016
SOIC - 2.65 mm max heightDW0020A
SOIC
SYMM
SYMM
LAND PATTERN EXAMPLE
SCALE:6X
1
10 11
20
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
DW0020A $$$$$fififiifi%
www.ti.com
EXAMPLE STENCIL DESIGN
(9.3)
18X (1.27)
20X (0.6)
20X (2)
4220724/A 05/2016
SOIC - 2.65 mm max heightDW0020A
SOIC
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
SYMM
SYMM
1
10 11
20
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:6X
MECHANICAL DATA W (R—GDFP—FZO) CERAWC DUAL FLATPACK Base and Szafing Hana (114111045 0.500 (7.62) f7 [1026 (0 as) 0.245 (6.22) f .: i ‘ ‘ 0.009 (023) fl? 0.004 0.10 <7 0.520="" (0.13)="" max="" 4»="" i="" 20="" :3="" i3:="" 0.022="" 0.56="" i:="" 3="" e="" )="" :i="" i:="" i="" 0.015="" (0.30)="" :3="" i:="" t="" :3="" ::i="" :3="" ::i="" 0.540="" (13.72)="" max="" [:3="" |::l="" [:3="" |::l="" [:3="" |::l="" [:3="" |::l="" “-005="" (m)="" m="" 4="" race:="" [:3="" i3:="" i="" 10="" i1="" 0="" 370="" (9,40)="" 0.370="" (9.40)="" 0.250="" (6.35)="" 0,250="" (5.35)="" 404013074/r="" 04/14="" notes:="" a.="" wpflw="" f0”:="" wilhin="" mh—std="" 1835="" gdfpz—fzo="" ah="" hnear="" dimensions="" are="" in="" inches="" (mhhmeters).="" this="" drawing="" ts="" sumeu="" \o="" cnange="" wunom="" nofice.="" this="" package="" can="" be="" hermelicahy="" semi="" win="" a="" ceramic="" lid="" using="" glass="" iril="" )ndex="" point="" is="" provided="" on="" cup="" (or="" lermina)="" identifica‘ion="" any.="" i="" texas="" instruments="" www.mmm="">
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated